RP-6 Type Pressure Reducing Valve (for Steam) Benten

VENN

Pilot operated general-purpose products (high-capacity) such as construction equipment, factory equipment, etc.

[Features]
· The VENN-TEN is a pilot-operated pressure reducing valve used in main pipes and large flow-rate lines of construction equipment, industrial steam circuits, various production equipment, system industries, etc.
・­ This pressure-reducing valve is designed with operability as the number 1 priority in this design. It has stable performance under various conditions, and it is easy to install and use because it is small and light.
· The adoption of the piston guide structure and special seal ring make control stable.
· Can be used for a wide range of pressures and flow rates.
▪ As for RP-6 type, it is easy to adjust the pressure by manual handle operation with automatic lock mechanism (nominal diameter 15 to 80).
· Compact design.

RD-14 Model Series - Pressure Reducing Valve (for Cold Water/Warm Water/Air/Oil)

VENN

Direct acting pressure reducing valve for air, liquids, and water has a low pressure fluctuating range and can be used at low as well as high flow rates.

[Features]
· At the construction facilities, the product can be used to control the pressure of water supplied from elevated water tanks in mid-rise and high-rise buildings, or in water supply directly connected to pumps instead of elevated water tanks, as well as in boiler water supply. Industrial use of the product includes pressure control for fuel oil, lubricating oil, and air.
· Has a pressure balance structure, so changes to set pressures are minimal.
· Maintenance is easy as the upper side can be taken apart unidirectionally allowing for internal inspection.
· RD-14CN models come with nylon coating to protect from red water.

VD-1H Type Vacuum Adjustment Valve

VENN

[Features]
▪ It prevents the suction of the air in a valve when it opens due to the decrease in set pressure and it also prevents the creation of vacuums in pipes and equipment.
▪ Using a silencer when the vapor pipe is attached prevents suction of water into the pipe when vapor stops generating.

Safety Relief Valve, AL-150TML Series

YOSHITAKE

Uses a lift valve lever mechanism for manually performing blowout inspections. The valve body/valve seat and adjustment spring are made from stainless steel. Anti-corrosive SCS14A is used in the main parts.

Pressure Reducing Valves (Steam), GD-6N Series

YOSHITAKE

Small, and lightweight, with constant secondary pressure accuracy even at small capacities. · The valve body and valve seat have superior durability thanks to the use of stainless steel.

[Features]
Constant secondary pressure accuracy does not change even at small capacities.
· Compact and lightweight.
· The valve body and valve seat have superior durability thanks to the use of stainless steel.
· A screen (60 mesh) is built in to protect the valve body and seat from foreign material, pipe scales, and pipe chips.

CAD ：

2D

Pressure Reducing Valves for Hot and Cold Water, GD-26-NE Series

YOSHITAKE

Corrosion-resistant materials are used in the liquid-contacting parts. Superior chlorine resistance and reliability for running cold and hot water. The valve utilizes pressure-balanced structure. Therefore, secondary side pressure is maintained at a fixed level without affecting the primary side pressure.

CAD ：

2D

RP-6P Type Pressure-Reducing Valve (for Steam), Benten

VENN

Pilot-operated general-purpose products (high-capacity) for construction equipment, factory equipment, etc.

[Features]
- The VENN-TEN is a pilot-operated pressure reducing valve used in main pipes and large flow-rate lines within construction equipment, industrial steam circuits, production equipment, system industries, etc.
­ Designed with operation as its highest priority, it has stable performance under many conditions, and its small size and light weight makes it easy to install and use.
- Piston guide structure and special seal ring for stable control.
- The RP-6 type is widely used in pressure range/flow rate applications. Its auto locking mechanism (nominal diameter from 15 to 80) makes pressure adjustment easy with manual handle control.
- Compact design.

RD-31N, 32N Type Pressure Reducing Valve, Heisei

VENN

Direct-acting general-purpose products (made of bronze, medium capacity) for use in construction equipment, factory equipment, etc.

[Features]
- Serves as a bronze water-pressure reducing valve meeting rust-water prevention needs.
- We combine our pressure-reduction technology with high controllability, reliability and user-friendliness, eliminating rust generation from pipe joints and across the flow path.
- Heisei provides reliable countermeasures for rusty water, used in building facilities, house facilities, plant facilities, boiler water supply, etc.
- Measures to prevent rusty water in normal state: Bronze body + pipe-end core to prevent rusty water.
- Low-noise design.
- Water does not leak outside if the diaphragm is damaged.
- Built-in strainer.
- (Nominal diameter of 50 or less 40 mesh equivalent) Smaller approximately 50% later than FC-made conventional parts.

Pressure Reducing Valve for Water, Hot Water, Air, RD-35F/36F Type, [Heisei]

VENN

· The [Heisei] series are pressure reducing valves for water made from bronze with stainless main parts. These valves combine corrosion resistance with controllability and reliability for compatibility in production plants, etc.

[Features]
· The SCS main body eliminates red water and it can also be used with stainless steel piping.
· A low-noise design.
· Smaller and lighter in weight by approx. 50% compared to conventional FC made parts.
· Water does not leak outside if the diaphragm is damaged.
· A pressure gauge can be installed directly onto the main body (secondary side only).

SL-35N/35HN Type, Relief Valve for Hot Water Equipment

VENN

Diaphragm type relief valve for small hot water boilers and electric water heaters. Used as a relief valve for pressure caused by thermal expansion and on the secondary side of pressure reducing valve.

FM Valve Type 1

FMVALVE

A valve that can be used in combination with electromagnetic valves and mechanical control valves.

[Features]
· This valve can be electrically controlled by combined use with electromagnetic valves. Therefore, it enables simple timed water rationing, and varying of supply start-stop intervals. In addition, it facilitates construction of effective water supply systems by combined use with sensors, etc., to match the usage conditions.
· This valve has simple structure. Therefore, it is easy to install and maintain.
· This valve has no flow adjustment mechanism. Therefore, the flow rate cannot be adjusted.

Safety Valve, Relief Valve AL-140 Series

YOSHITAKE

[Features]
・ It is made entirely of stainless steel, SCS14A (equivalent to SUS316) with excellent corrosion resistance is used for the main part
・ The sealed structure prevents fluid from leaking to the outside

Safety Valve, Relief Valve AL-150 Series

YOSHITAKE

[Features]
・ It is a versatile type that supports fluids such as steam, air, water, and oil
・ The pressure division was subdivided, and ultra-precise finishing by advanced technology was realized to pursue the best performance
・ Main parts (valve body, valve seat) and adjustment spring are made of stainless steel, and SCS14A (equivalent to SUS316) with excellent corrosion resistance is used for main parts
・ The sealed structure prevents fluid from leaking to the outside

Safety Relief Valve AL-300/AL-301 Series

YOSHITAKE

[Features]
▪Mainly used in safety relief values after pressure reducing valves and in safety valves such as small boilers and various pressure containers and instruments.
· The AL-301 has stainless steel main components (valves and valve seats), so it offers superior corrosion resistance and durability.

CAD ：

2D

Pressure Reducing Valves (Hot and Cold Water, Oil, Air), GD-200/GD-200H Series

YOSHITAKE

A high-capacity type that can also handle high pressures. Optimal for use as industrial equipment.

CAD ：

2D

Pressure Reducing Valve (For Cold and Hot Water) GD-24GS/GD-24GS-N Series

YOSHITAKE

A hanging metal type. A pressure reducing valve without sliding parts. Requires maintenance of consumable parts only.

Door-to-Door Water Supply Pressure Reducing Valve and Directional Control Valve, CV-36UL/CV-36UK Series

YOSHITAKE

Fitting with a built-in check valve for the GD-46 / 38 series of pressure reducing valves with bypass for door-to-door water supply in housing complexes.

Pressure Reducing Valve for Water Supply, GD-56-80 Series

YOSHITAKE

It's used for the purpose of water supply of hot water for the heat exchanger, and then used maintaining a predetermined water supply pressure. In addition to the pressure reducing function, a backflow prevention function, a negative-pressure operation function, a pressure balancing function, and a strainer are built in.

CAD ：

2D

RD-41F Pressure-Reducing Valve (for Vapor), Mini Benten

VENN

For food machinery, medical equipment, laundry equipment, and other steam-based machinery/equipment

[Features]
- A direct-acting pressure reducing valve, ideal for the precise control of steam pressure.
- Compact and lightweight; best for integrating into devices.
- Good for items that need to be free of rust, such as food/kitchen equipment, medical equipment, laundry machines, and air conditioners (humidifiers).
- Stainless steel body for higher-grade vapor lines.
- Helps guarantee the large (heat) flow rates necessary to start up equipment.
- Main body made of bronze or stainless steel; main parts are made of stainless steel for clean vapor.
- Secondary side pressure can be smoothly adjusted with the manual handle for the automatic lock mechanism.
- Uses SUS316L bellows, equipped in the strainer and is highly durable.

Pressure Reducing Valve for Steam, Gas and Liquid, RD-3H Series

VENN

[Features]
· Pilot type direct-acting, pressure-reducing valve that is used in non-controllable, small flow-rate locations. It has good pressure-control with excellent wide pressure range adjustment characteristics. The main parts are made from SUS (for steam).
· Note: These valves differ for use with stream, air, vapor, and liquid.

RD-31FN, 32FN Type, Pressure-Reducing Valve HEISEI

VENN

Direct acting type general-purpose products (made of bronze, medium capacity) such as construction equipment, factory equipment, etc.

[Features]
· Calm-flow rusty water countermeasures: Bronze body + Pipe-end core, to prevent rusty water.
· Low noise design.
· Smaller and more lightweight by 50% than FC made conventional parts.
▪ Water does not leak outside when diaphragm is damaged.
▪ Built-in strainer (Equivalent to 40 mesh with nominal diameter of 50 or less).
· Heisei serves as a bronze water pressure reducing valve meeting the needs of the times [trump card to prevent rusty water].
▪Already highly winning high praise, it combines technology of pressure reducing valves for water, with controllability, reliability, and user-friendliness, eliminating rust generation from the flow path including pipe joints in particular.
· [Heisei] is receiving increased reputation in active countermeasures for rusty water and is used for building facilities, house facilities, plant facilities, boiler water supply, etc.

RD-47N Pressure-Reducing Valve for Door-to-Door Water Supply (for Cold/Hot Water), Benkei

VENN

Pressure reducing valve for hot and cold water supply used in apartment buildings, high-rise buildings, etc.

[Features]
· Water supply pressure reducing valve per room unit results in: 1) Reduces flow noise. 2) Eliminates water supply pressure variation difference with elevation difference. 3) No water splashes due to application of appropriate pressure. 4) During maintenance, impact of water outage does not affect wide area. 5. Stable mixing temperature resulting in improved habitability.
· Uses chlorine water-resistant EPDM.
· Sanitary design avoids pooling of liquids.
· Works reliably from low differential pressures to high differential pressure.
· Easy, simple new test gag method.
· Safe and secure construction is made possible due to intact pressure-reducing valves.
· You can conduct a hydraulic test even after construction while the pressure reducing valve is installed.
▪ Cassette type valve enables easy maintenance.
· With a structure without caulking or welding, all components are recyclable and can be segregated and disposed.

LP-8N Type, Water Level-Regulating Valve (for Water and General Use)

VENN

A water-level regulating valve for general water tanks that, apart from the insertion type structure of the bronze body and tube end core, has been simplified and made more compact by removing all adjusting mechanisms. Helps prevent rusty water.

[Features]
• Countermeasure for rusty water: Threaded type - The bronze body + pipe end core can be inserted.
• A bypass flow path is used for the passage to the pilot piping, facilitating a quiet and stable water supply and ensuring that, even if the water supply from the ball tap is temporarily cut due to surges, water will still be available.
• Since the valve is simple and compact, handling is easy.
• Antifreezing FV jackets are provided.

LP-8HN Level-Regulating Valve (for Water, for General Use with Adjustment Mechanisms)

VENN

[Features]
· Standard constant water level valve with adjusting mechanism.
· In order to prevent rust, threading can be bronze and embedded in the pipe end core.
· A flow-rate adjustment mechanism and a valve closing time adjustment needle are provided.
· Solution for rusty water: Screw-in = Bronze body + Pipe end core assembly is possible.
· Because a bypass flow path is used for the passage to the pilot piping, intermittent water supply effects due to surges are eliminated, providing a silent and steady water supply.
· Antifreeze FV jacket is provided.

AF-4 Series Air Vent Valve

VENN

The equipment is used in building facilities and factory facilities, etc. It is an air vent valve for fluids. It automatically discharges the air that accumulates in the pipes and the air inside an airtight tank and makes the fluid flow smoothly.

[Features]
▪ Due to the improved airtightness, it has adopted the swing valve body.
▪ The amount of air discharged from the equipment is comparatively large.
▪ It has a simple structure that allows easy handling.
· AF-4CN is a rust-resistant nylon-coated product.

AF-10 Series, Air Vent Valve

VENN

A stainless steel air relief valve with excellent corrosion resistance and durability, with a strainer built-in to the main body, and with air intake and exhaust functions.

[Features]
· Easy design installation possible with the built-in strainer.
· Stainless steel with superior corrosion resistance and durability.
· The discharge port can be freely rotated 360°, so installation is simple.
· Equipped with a manual shut-down control.

AF-9 Series Air Vent Valve

VENN

Air vent valve with built-in check valve such as pump suction side or sealed circuit

[Features]
· Air vent valve made of stainless steel with built-in strainer in the main body that boasts superior corrosion resistance and durability. The AF-10 type series has air intake and exhaust functions.
· AF-9 type series is an air vent valve with a built-in check valve and is structured to not intake here even when the inlet side is exposed to negative pressure. Hence, it is used when a function is required for only emitting and not in taking the air, such as in the pump suction inlet side and degassing system of sealed circuits.
· Easy design construction possible with the built-in strainer.
· Made of stainless steel for superior corrosion resistance and durability.
· The exhaust vents can be freely rotated 360° and are easy to work with.
· Equipped with manual shut-down control.
· Does not absorb air even when the pressure is negative, and therefore can be mounted into the pump suction inlet side.

Relief Valve, AL-250 Series

YOSHITAKE

[Features]
・ Since it is entirely made of stainless steel, it has excellent corrosion resistance and durability
・ By adopting a dashpot structure, it has a great effect on lines with large pulsations and pressure fluctuations. Chattering and hunting are reduced
・ It has stable operation against back pressure changes during continuous blowing

CAD ：

2D

Relief Valve, AL-260 Series

YOSHITAKE

[Features]
・ Main parts are made of stainless steel, and all wetted parts are made of corrosion resistant material
・ By adopting a dashpot structure, it has a great effect on lines with large pulsations and pressure fluctuations
・ Chattering and hunting are reduced
・ It has stable operation against back pressure changes during continuous blowing

Safety Relief Valve, AL-140T Series

YOSHITAKE

[Features]
・ Since it is entirely made of stainless steel, it has excellent corrosion resistance and durability
・ A soft seat is used for the main part, and it has excellent airtightness in the valve seat
・ It is ideal for applications where valve seat leakage cannot be tolerated
・ The sealed structure prevents fluid from leaking to the outside

CAD ：

2D

Safety Relief Valve, AL-150L Series

YOSHITAKE

[Features]
· The main parts (valve body and seat) and adjustment springs are made of stainless steel; in particular, the main parts use SCS14A (equivalent to SUS316) which has excellent corrosion resistance.
· With lift valve lever types, discharge inspections can be performed manually at a pressure that is 75% or more of the discharge pressure.

CAD ：

2D

Safety Relief Valve, AL-150TR Series

YOSHITAKE

A handle-operated valve for changing the pressure easily. Usable as a relief valve.

[Features]
· The AL-150 is a handle-operated valve for changing the pressure easily. Therefore, this valve can be used as a relief valve.
· Soft seats are utilized in the main parts for a superior valve seat airtight performance.
· Optimal for applications in which valve seat leaks are unacceptable.
· The main parts (valve body and seat) and adjustment springs are manufactured from SCS14 stainless steel (SUS316 EQUIV) with excellent anti-corrosive properties.
· The sealed construction prevents fluid from leaking outside.

Safety Relief Valve, AL-150T Series

YOSHITAKE

[Features]
· Soft seats are utilized in the main parts for a superior valve seat airtight performance. Optimal for applications in which valve seat leaks are unacceptable.
· The main parts: valve body, seat. and adjustment springs are made from stainless steel. Anti-corrosive SCS14A is used for the main parts.
· The sealed construction prevents liquid from leaking outside.

Safety Relief Valve AL-300T/AL-301 T Series

YOSHITAKE

[Features]
・ Fluoropolymer disc is used for the valve, so it has excellent seat airtightness
・ The main part (valve body / valve seat) of AL-301T is stainless steel, which has excellent corrosion resistance and durability

CAD ：

2D

Safety Relief Valve, AL-4T Series

YOSHITAKE

[Features]
· Mainly used as a safety relief valve downstream of a pressure reducing valve, safety valve for various pressure vessels and instrumentation equipment, and relief valve for pumps.
· Fluororesin disks are used in AL-4T valve parts for superior valve seat sealing.

Intake Valve - Automatic Intake Valve - VB-10 Series

YOSHITAKE

[Features]
• This valve increases atmospheric pressure by applying air to the pipe from which it is difficult to drain the water. Consequently, water is easily drained during water drainage operations.
• As a 60-mesh strainer is built into the valve, there are no blockages due to scale.
• In addition, even if water leaks due to blockage, water can be stopped by tightening the cap.
• As the highest temperature is 95°C, warm water is also supported.
• Can be mounted in both vertical and horizontal directions (Downward facing not possible).

Intake and Exhaust Valves, TAV-2 Series

YOSHITAKE

Quickly prevents air from being sucked back when negative pressure occurs. Automatically works in response to air intake and exhaust requirements.

CAD ：

2D

Air Vent Valve TA-16CVA, Series

YOSHITAKE

Provides a stable displacement across a wide range of operating pressures (0.01–1.0 MPa). Compact design permits installation in small space. Included check valve prevents air being sucked in on inlet side, even at negative pressure.

CAD ：

2D

Air Vent Valve, TA-16 CVS Series

YOSHITAKE

[Features]
・ All materials other than valve discs, gaskets, check valves, check valve fitting are made of stainless steel
・ Wide operating pressure (0.01 to 1.0 MPa) gives stable displacement
・ Compact size allows installation in a small space
・ Excellent sealing performance because synthetic rubber is used for the valve disc
・ TA-16CVS makes it easy to connect any exhaust pipe by installing optional pipe connection parts
・ Since it has a check valve, it does not suck air even when the inlet side is under negative pressure
[Applications]
・ building equipment, factory equipment, housing complex

CAD ：

2D

Air Vent Valve TA-16L Series

YOSHITAKE

[Features]
・ All materials other than valve discs, gaskets and L-shaped hose fittings (TA-16L) are made of stainless steel
・ Wide operating pressure (0.01 to 1.0 MPa) gives stable displacement
・ Compact size allows installation in a small space
・ Excellent sealing performance because synthetic rubber is used for the valve disc
[Applications]
・ building equipment, factory equipment, housing complex

CAD ：

2D

Air Vent Valve TA-16 Series

YOSHITAKE

Provides a stable displacement across a wide range of operating pressures (0.01–1.0 MPa). Its compact size enables mounting in a narrow space.

[Features]
• All parts are made of stainless steel, except for the valve body disk, gasket, and L-hose fitting (TA-16L), which ensures excellent corrosion resistance and durability.
• The valve body disk is made of fluororubber, which ensures excellent sealing performance.
• The TA-16 can easily be connected to an exhaust pipe by mounting the optional pipe connectors.

CAD ：

2D

Air Vent Valve, TA-3/TA-6 Series

YOSHITAKE

Operates at a wide range of pressures, allowing use from low to high pressures. The valve seat uses a synthetic rubber disk, preventing leakage from the valve, but as a precautionary measure a screw has been added to mount the copper tube fitting onto the top part of the valve seat.

CAD ：

2D

Pressure Reducing Valve (Steam), GP-1000S Series

YOSHITAKE

[Features]
・ It complies with SHASE-S106 pressure reducing valve (The Society of Heating, Air-Conditioning and Sanitary Engineers of Japan) standards
・ Since the main valve has a spherical shape, it has excellent sealing performance and the amount of valve seat leakage is significantly reduced (Compliant with ANSI Class IV)
・ When compared with conventional pressure reducing valves, workability and durability are significantly enhanced

Pressure Reducing Valve (For Steam / Low Pressure) GP-1000 Series

YOSHITAKE

[Features]
▪ SHASE-S106 conforms to standards of pressure reducing valve (Air Conditioning and Health Engineering Society).
· The spherical shape of the main valve has excellent sealing properties to reduce valve seat leakage significantly (corresponding to the ANSI class IV) .
· Compared with conventional pressure reducing valves, workability and durability are significantly enhanced.

Pressure Reducing Valves for Hot and Cold Water / Oil/Air, GD-6 Series

YOSHITAKE

Small, and lightweight, with constant secondary pressure accuracy even at small capacities.

CAD ：

2D