Can linear guides or sliders be purchased separately?

Taking into account the accuracy of products, single slider models clearly indicated in the catalog can be purchased, and no others can be purchased.

Can the stainless steel guide rails be guaranteed not to rust?

Stainless steel is a product that has a certain antirust function compared to carbon steel, but it cannot be guaranteed that it will never rust. Depending on the operating environment, there may also be short-term rust.

What problems should be paid attention to when the linear guide is installed vertically?

Attention should be paid to prevent the slider from falling off and causing the balls to fall off during installation.

What does micro preloading in linear guide mean?

MISUMI's linear guides control the clearance by selecting the size of the internal ball. Through the negative clearance, the rigidity is improved and the elastic displacement is reduced. This is preloading. Generally speaking, the life and accuracy of the micro preloading type will be better than that of the standard clearance type.

Linear guide indicators include basic dynamic load rating and basic static load rating. Which indicator is the reference when selecting?

The basic dynamic load rating is used to calculate the rail life, and the basic static load rating is used to calculate the maximum allowable load.

Can the corresponding linear guide products be selected according to the third-party guide rail model?

MISUMI offers third-party brand replacement services, so as long as the third party product model is given, we can replace it with corresponding MISUMI model. For details, please contact the customer service email or call the customer service phone.

Can the rail or slider be repaired if it is damaged?

Repair service is not provided, re-purchase is recommended.

Can linear guide length be arbitrarily specified?

It can be specified arbitrarily. However, MISUMI linear guides are divided into length fixed type and length specified type, and in case of length specified type, the length dimensions for length fixed type cannot be specified.

Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(12 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

E-GMLGW7-[50-900/1]

Rail Length L Block Type Assembly Height H Nominal Part Number Rail Type Set / Single Item Preload Accuracy Standards No. of Blocks Lubrication Type Lubrication Type L Dimension Type Applicable Linear Guide Block Material (Surface Treatment) Rail Material (Surface Treatment) Rail Surface Treatment Material CAD Days to Ship

Specification/Dimensions

Rail Length L(mm)
[50-900/1mm Unit(s)]
Clear
Block Type
- Standard
  - Standard Block
Clear
Assembly Height H(mm)
9

12

14

16
Clear
Nominal Part Number
7

9

12

15
Clear
Rail Type
- Wide Rail
Clear
Set / Single Item
- Set
- Block Only
Clear
Preload
- Clearance
  - Normal Clearance
Clear
Accuracy Standards
- Standard Grade
Clear
No. of Blocks
- 1
Clear
Lubrication Type
- Lubrication Applied
Clear
Lubrication Type
- Lithium Grease Filled
Clear
L Dimension Type
- Specified Type
Clear
Applicable Linear Guide
E-GMLGW7

E-GMLGW9

E-GMLGW12

E-GMLGW15
Clear
Block Material (Surface Treatment)
- Carbon Steel (Bearing Steel)
- Stainless Steel
Clear
Rail Material (Surface Treatment)
- Carbon Steel (Bearing Steel)
- Stainless Steel
Clear
Rail Surface Treatment
- Vacuum evaporated chrome plating
- none
Clear
Material
- Carbon Steel
- Stainless Steel
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

Same day

3 Day(s) or Less

13 Day(s) or Less

15 Day(s) or Less
Clear

Specify Alterations

Miniature Linear Guides Wide Rails

Volume Discount

Check FAQ of this product (8 items)

Brand :

MiSUMi Economy

Part Number :

E-GMLGW7-[50-900/1]

Order Qty :
Price :

---
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Product Description

Miniature Linear Guides Wide Rails
These linear guides or linear slides are an economy item, The price is cheaper than the MISUMI standard product. They offer a wide variety of sizes to choose from.
[Feature]
● Rail Length Minimum/Maximum (mm.): 50 and 670
● Assembly Height (mm.): 9, 12, 14 and 16
● Rail Type : Wide Rail
● Option: Set (Rail + Block) / Block only
● Material: Rail- Bearing steel, Block - SUS440C
[Application]
It is used in a variety of machines such as CNC machines, 3D printers, measuring instruments, and so on.

Economy Miniature Wide Rail Linear Guide

DurabilityWide RailAffordable

- Rail lengths available in multiple options

- Multiple assembly heights available

- Available as a set or block only

- Constructed from Carbon Steel and Stainless Steel

- Affordable alternative to standard products

Economy Miniature Wide Rail Linear Guide

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product Overview

Linear guides (also known as slide rails or linear slides) are designed for precise linear motion and are used in high-precision applications. They provide higher load capacity and motion accuracy than linear bearings of the same size. These guides use rolling elements (such as steel balls) instead of an intermediate medium, allowing for smooth, precise movement even under high load conditions. They are commonly used in equipment like CNC machines, robotics, and automated systems.

Product Comparison

	MISUMI Standard Product SSEBWL9-100	Economy Series E-GMLGW7-100
Material	Stainless Steel	Carbon Steel
Hardness	56HRC up	58HRC up
Basic Rated Load C (Dynamic) (kN)	1.4	1.37
Basic Rated Load Co (Static) (kN)	2.2	2.06
Static Allowable Moment MA/MB (N・m)	7.8	7.14
Static Allowable Moment MC (N・m)	15.5	15.7
Height H Tolerance Difference (μm)	±20	±20
Height H Pair Variation Difference (μm)	15	40
Width N Tolerance Difference (μm)	±25	±25
Width N Pair Variation Difference (μm)	20	40
Running Parallelism Guarantee (μm)*	7	15
Preload Management	Y	N
RoHS10	Compliant	Compliant

*Running parallelism varies by rail length.

Dimensional Drawing

MISUMI Miniature Linear Guide Slider dimension drawing

■ Material

Type	Material		Rail Surface Treatment	Hardness	Preload
	Guide Rail	Block
E－MLGW	Bearing Steel	Stainless Steel	-	58-62HRC	Z0 Ordinary Grade No Gap Type
E－GMLGW			Vacuum evaporated chrome plating
E－SMLGW	Stainless Steel		-	55-58HRC
E－SMLGWB	-	Stainless Steel	-	-

For vacuum chrome plating products(E-GMLGW), the cut surface on both ends is not treated.

Specification Table

■ Component kit

Part Number		Length L (1mm increments)	Block Dimensions (mm)									Rail Dimension (mm)
Type	Nominal Model	Length L (1mm increments)	W	B	B₁	L₁	L₂	C	M×ℓ	H₂	Gn	H	H₁	N	H_R	W_R	W_B	Counterbore d×D×h	P	E
E-MLGW E-GMLGW E-SMLGW	7	50～900	25	19	3	21	30.9	10	M3×3	1.85	Φ1.2	9	1.9	5.5	5.2	14	-	3.6×6×3.2	30	Please refer to the calculation table below
	9	50～900	30	21	4.5	27.5	38.44	12	M3×3	2.4		12	2.9	6	7	18		3.6×6×4.5	30
	12	70～900	40	28	6	31.3	45.05	15	M3×3.6	2.8		14	3.4	8	8.5	24		4.5×8×4.5	40
	15	70～900	60	45	7.5	38	54.19	20	M4×4.2	3.2	M3	16	3.4	9	9.5	42	23	4.5×8×4.5	40

■ Single Block

Part Number		Block Dimensions (mm)
Type	Nominal Model	W	B	B₁	L₁	L₂	C	Mxℓ	H₂	Gn
E-SMLGWB	7	25	19	3	21	30.9	10	M3×3	1.85	Φ1.2
	9	30	21	4.5	27.5	38.44	12	M3×3	2.4
	12	40	28	6	31.3	45.05	15	M3×3.6	2.8
	15	60	45	7.5	38	54.19	20	M4×4.2	3.2	M3

The dimensional tolerance of L length is ±1mm and

The dimensional tolerance of E end distance is ±0.5mm

■ L Detailed dimension of dimension specified type
Dimension L specified type cuts both ends of the rail equally. Refer to the table below for the number of mounting holes (M) of the slide rail at this time.
In addition, E dimension is calculated with the formula below.
Economy series Linear Guide Length Specified Type E Dimension Calculation Formula

Economy series Linear Guide Length Specified Type E Dimension Calculation Formula

L : Guide Rail length
M: Guide Rail mounting holes
P: Guide Rail holes pitch

Miniature Linear Guides Wide Rails -Standard rail-

Nominal Model	7	9	12	15	Number of mounting holes M
L	50～67	50～67	70～89	70～89	2
	68～97	68～97	90～129	90～129	3
	98～127	98～127	130～169	130～169	4
	128～157	128～157	170～209	170～209	5
	158～187	158～187	210～249	210～249	6
	188～217	188～217	250～289	250～289	7
	218～247	218～247	290～329	290～329	8
	248～277	248～277	330～369	330～369	9
	278～307	278～307	370～409	370～409	10
	308～337	308～337	410～449	410～449	11
	338～367	338～367	450～489	450～489	12
	368～397	368～397	490～529	490～529	13
	398～427	398～427	530～569	530～569	14
	428～457	428～457	570～609	570～609	15
	458～487	458～487	610～649	610～649	16
P	30	30	40	40

Nominal Model	7	9	12	15	Number of mounting holes M
L	488～517	488～517	650～689	650～689	17
	518～547	518～547	690～729	690～729	18
	548～577	548～577	730～769	730～769	19
	578～607	578～607	770～809	770～809	20
	608～637	608～637	810～849	810～849	21
	638～667	638～667	850～889	850～889	22
	668～697	668～697	890～900	890～900	23
	698～727	698～727	－	－	24
	728～757	728～757			25
	758～787	758～787			26
	788～817	788～817			27
	818～847	818～847			28
	848～877	848～877			29
	878～900	878～900			30
P	30	30	40	40

Alterations

Code

Spec.

Change to Tapped Holes

Ordering code: MC
Change counterbored holes for fixing a guide to tapped holes.

Nominal size	MC
7	M3
9,12	M4
15	M5

2-Block Specifications

1 block added to 1-block product to ship as 2 block item.

If the rail is too short to fit multiple blocks, the blocks will be shipped in a separate package.

3-Block Specifications

2 blocks added to 1-block product to ship as 3 block item.

If the rail is too short to fit multiple blocks, the blocks will be shipped in a separate package.

4-Block Specifications

3 blocks added to 1-block product to ship as 4 block item.

If the rail is too short to fit multiple blocks, the blocks will be shipped in a separate package.

Preload adjustment

Change Z0: zero preload to
ZF: Normal clearance
Z1: Light preload
Z2: Medium preload

Rail End Cut

Left End Cut
ES

Specify the edge distance in 0.5 mm increments. When the specified edge distance exceeds or is close to the hole spacing, cutting may result in hole breakage.

EB + ES = 2E. In cases where cutting is not feasible, distribute the dimensions evenly according to the standards.

Right End Cut
EB

Precision Benchmark

●Dimensional Precision

Dimensional Precision Type	Precision Standard	Misumi
Miniature	Height H Tolerance	±40
	Height H Pair Variation	40
	Width N Tolerance	±40
	Width N Pair Variation	40

●Running Parallelism

Rail Length (mm)	Accuracy grade (μm)
Less than 50	12
50-80	13
80-125	15
125-200	15
200-250	16
250-315	17
315-400	18
400-500	19
500-630	20
630-800	22
800-900	23

[Running Parallelism]
The values in the table are measured after the slide rail is fixed on the base.
When moving the slider within the entire length of the slide rail, measure the change of the upper surface C of the slider relative to the bottom surface A of the slide rail, and the change of the reference surface D of the slider relative to the reference surface B of the slide rail.
When moving the sliding block within the entire length of the slide rail, measure the change of the upper surface C of the slider relative to the bottom surface A of the slide rail, and the change of the reference surface D of the slider relative to the reference surface B of the slide rail.

Allowable Load

Nominal Model	Basic Rated Load		Static Allowable Moment		Mass
Nominal Model	C (Dynamic) kN	Co (Static) kN	M_A・M_B kN-m	M_C kN-m	Blocks kg	Guide Rails kg/m
7	1.37	2.06	7.14	15.7	0.02	0.51
9	2.75	4.12	18.96	40.12	0.04	0.91
12	3.92	5.59	27.8	70.34	0.071	1.49
15	6.77	9.22	56.66	199.34	0.143	2.86

Product Features

Feature 1: New construction, greatly reducing noise and improving smoothness.
Feature 2: The slide rail and the slider are in contact with each other through the rolling ball, so the shaking is small, and it is suitable for equipment with precision requirements.
Feature 3: Due to a point-to-surface contact, the frictional resistance is small, and it can perform subtle movements to achieve high precision positioning of the control device.
Feature 4: It has a large allowable load because the force on the rotating surface is dispersed due to the rolling groove of the ball.
Feature 5: It is suitable for high speed motion because it is not easy to produce friction heat when operating and not easily deformed by heat.

Usage Method

■ About use
① MISUMI's linear guide is installed with a retainer. Although the ball is not easy to fall off when the slide block is removed, the ball may fall off if the slider is removed from the rail at high speed, or tilted into the slide rail. Please disassemble the slider with care.
② Be sure to avoid colliding the ball back groove cover, otherwise it will affect the ball cycling, resulting in poor sliding.
③ If you have anti-rust requirements, please choose the Vacuum Chrome Plating Surface Treatment or Stainless Steel SUS440C products.
MISUMI Miniature Linear Guide Slider Precautions

■ About maintenance (supply of grease)
① Grease forms an oil film on the surface of the linear guide ball and rail surface to effectively reduce friction and prevent sintering.
Decrease and aging of grease will greatly affect the life of the linear guide, so please add grease at the right time according to the service conditions.
MISUMI's linear guides are sealed with the greases listed below at the time of shipment, so they can be used directly.
② Recommend grease filling interval:
Usually every 6 months.
For longer moving distance, 3 months, or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.
*The above is the grease injection interval under the moving distance standard. Depending on the operating environment, the grease injection interval must be shortened appropriately when the grease is aging and dirty.

Precautions

For normal use, the installation of the linear guide needs to meet the following four points:

① Whether the shape of the mounting surface produces interference
Flatness of MISUMI mounting surface

② Keep the flatness of the workpiece mounting surface at about 5μ, otherwise the slider will be slightly deformed
MISUMI parallelism error tolerance

③ Whether the error values of guide parallelism and fitting height are within the allowable installation values
Allowable height error tolerance of linear-guides

Allowable height error tolerance of linear-guides

④ Use the standard
Installation method of linear guides

installation method Click

here for the detailed installation method

Example of Use

Mechanism Name: 4 times stroke slide
Feature 1: suitable for medium frequency driving and positioning.
Feature 2: transfer the light workpiece on the worktable according to 4 times the distance of the cylinder stroke.

For details, click

here

Application Industries

Medical		Smart phone

Robotics		Electronic & Electrical Appliances

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 45; 60

Part Number
E-GMLGW7-[50-900/1]
E-GMLGW9-[50-900/1]
E-GMLGW12-[70-900/1]
E-GMLGW15-[70-900/1]
E-MLGW7-[50-320/1]
E-MLGW9-[50-900/1]
E-MLGW12-[70-470/1]
E-MLGW15-[70-670/1]
E-MLGWB7
E-MLGWB9
E-MLGWB12
E-MLGWB15

Price	Minimum Order Qty.	Volume Discount	Days to Ship	RoHS	Rail Length L (mm)	Block Type	Assembly Height H (mm)	Nominal Part Number	Rail Type	Set / Single Item	Preload	Accuracy Standards	Material	No. of Blocks	Lubrication Type	Lubrication Type	L Dimension Type	Applicable Linear Guide	Block Material (Surface Treatment)	Rail Material (Surface Treatment)	Rail Surface Treatment
-	1 Piece(s)		3 Day(s)	10	50 ～ 900	[Standard] Standard Block	9	7	Wide Rail	Set	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	1	Lubrication Applied	Lithium Grease Filled	Specified Type	-	Carbon Steel (Bearing Steel)	Carbon Steel (Bearing Steel)	Vacuum evaporated chrome plating
-	1 Piece(s)		3 Day(s)	10	50 ～ 900	[Standard] Standard Block	12	9	Wide Rail	Set	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	1	Lubrication Applied	Lithium Grease Filled	Specified Type	-	Carbon Steel (Bearing Steel)	Carbon Steel (Bearing Steel)	Vacuum evaporated chrome plating
-	1 Piece(s)		3 Day(s)	10	70 ～ 900	[Standard] Standard Block	14	12	Wide Rail	Set	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	1	Lubrication Applied	Lithium Grease Filled	Specified Type	-	Carbon Steel (Bearing Steel)	Carbon Steel (Bearing Steel)	Vacuum evaporated chrome plating
-	1 Piece(s)		3 Day(s)	10	70 ～ 900	[Standard] Standard Block	16	15	Wide Rail	Set	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	1	Lubrication Applied	Lithium Grease Filled	Specified Type	-	Carbon Steel (Bearing Steel)	Carbon Steel (Bearing Steel)	Vacuum evaporated chrome plating
-	1 Piece(s)		3 Day(s)	10	50 ～ 320	[Standard] Standard Block	9	7	Wide Rail	Set	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	1	Lubrication Applied	Lithium Grease Filled	Specified Type	-	Carbon Steel (Bearing Steel)	Carbon Steel (Bearing Steel)	none
-	1 Piece(s)		3 Day(s)	10	50 ～ 900	[Standard] Standard Block	12	9	Wide Rail	Set	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	1	Lubrication Applied	Lithium Grease Filled	Specified Type	-	Carbon Steel (Bearing Steel)	Carbon Steel (Bearing Steel)	none
-	1 Piece(s)		3 Day(s)	10	70 ～ 470	[Standard] Standard Block	14	12	Wide Rail	Set	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	1	Lubrication Applied	Lithium Grease Filled	Specified Type	-	Carbon Steel (Bearing Steel)	Carbon Steel (Bearing Steel)	none
-	1 Piece(s)		3 Day(s)	10	70 ～ 670	[Standard] Standard Block	16	15	Wide Rail	Set	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	1	Lubrication Applied	Lithium Grease Filled	Specified Type	-	Carbon Steel (Bearing Steel)	Carbon Steel (Bearing Steel)	none
₹ 2,226.00	1 Piece(s)	Available	Same day	10	-	[Standard] Standard Block	9	7	Wide Rail	Block Only	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	-	-	-	-	E-GMLGW7	Carbon Steel (Bearing Steel)	-	-
₹ 2,486.00	1 Piece(s)	Available	Same day	10	-	[Standard] Standard Block	12	9	Wide Rail	Block Only	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	-	-	-	-	E-GMLGW9	Carbon Steel (Bearing Steel)	-	-
₹ 2,679.00	1 Piece(s)	Available	Same day	10	-	[Standard] Standard Block	14	12	Wide Rail	Block Only	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	-	-	-	-	E-GMLGW12	Carbon Steel (Bearing Steel)	-	-
₹ 3,051.00	1 Piece(s)	Available	Same day	10	-	[Standard] Standard Block	16	15	Wide Rail	Block Only	[Clearance] Normal Clearance	Standard Grade	Carbon Steel	-	-	-	-	E-GMLGW15	Carbon Steel (Bearing Steel)	-	-

Basic Information

Ball Arrangement	Miniature Type	Retainer	N/A	Rolling Element	Ball

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: Can linear guides or sliders be purchased separately?: Answer: Taking into account the accuracy of products, single slider models clearly indicated in the catalog can be purchased, and no others can be purchased.
Question: Can the stainless steel guide rails be guaranteed not to rust?: Answer: Stainless steel is a product that has a certain antirust function compared to carbon steel, but it cannot be guaranteed that it will never rust. Depending on the operating environment, there may also be short-term rust.
Question: What problems should be paid attention to when the linear guide is installed vertically?: Answer: Attention should be paid to prevent the slider from falling off and causing the balls to fall off during installation.
Question: What does micro preloading in linear guide mean?: Answer: MISUMI's linear guides control the clearance by selecting the size of the internal ball. Through the negative clearance, the rigidity is improved and the elastic displacement is reduced. This is preloading. Generally speaking, the life and accuracy of the micro preloading type will be better than that of the standard clearance type.
Question: Linear guide indicators include basic dynamic load rating and basic static load rating. Which indicator is the reference when selecting?: Answer: The basic dynamic load rating is used to calculate the rail life, and the basic static load rating is used to calculate the maximum allowable load.
Question: Can the corresponding linear guide products be selected according to the third-party guide rail model?: Answer: MISUMI offers third-party brand replacement services, so as long as the third party product model is given, we can replace it with corresponding MISUMI model. For details, please contact the customer service email or call the customer service phone.
Question: Can the rail or slider be repaired if it is damaged?: Answer: Repair service is not provided, re-purchase is recommended.
Question: Can linear guide length be arbitrarily specified?: Answer: It can be specified arbitrarily. However, MISUMI linear guides are divided into length fixed type and length specified type, and in case of length specified type, the length dimensions for length fixed type cannot be specified.

Check other FAQ (5 items) Hide

Miniature Linear Guides	Medium Load linear guide	Heavy Load linear guide

Typical model: SSEBZ10-55	Typical model: SVR24-280	Typical model: SXR24-280

Search by Category / Brand

Search by Category

How can we improve?