Why is the order model of the timing belt inconsistent with the actual belt label and engraving?

Order model is MISUMI product model, the label on the belt or printed model on the belt surface is the belt manufacturer model, which varies with manufacturer, but there will be no influence on the product itself.

The timing belt has been broken after use for a very short period of time. Is there a problem with the quality of the belt?

The timing belt is a standard product, and the same batch of products have very few individual quality problems, please refer to 【Main causes of premature breakage and corresponding countermeasures】 to troubleshoot the equipment in use.

Can alteration be made to the timing belt?

Alteration cannot be made to the circumference of the timing belt, and partial alteration can be made to the width.

What kind of belt is better to use under conditions that require high cleanliness?

The use of urethane belts is recommended, which has significantly improved dust drop, compared to the rubber belt.

What are the two main types of timing belts according to their functions? What is the role?

Timing belts are mainly divided into transmission type and driving type. For transmission type, the load can be placed on the timing belt surface for transmission. For driving type, no load is carried, and only the role of transmitting torque is played, which is similar to the role of chain.

How to judge or measure whether the belt tension meets the installation requirements?

It is recommended that the customer purchase the tension meter by himself and make a judgment according to the calculation formula of the initial design.

Which tooth type of the timing belt has the smallest clearance? What will it affect?

The arc tooth type has minimum clearance, which can improve such indicators as positioning accuracy and rigidity.

Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(1 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

C-HTBN945H3M-90

type Belt Width (mm) Circumference Length Number of Teeth CAD Days to Ship

Specification/Dimensions

type
- C-HTBN□□H3M
Clear
Belt Width (mm)(mm)
6

9

12

15
Clear
Circumference Length(mm)
90

99

105

108

111

120

123

126

129

132

135

141

144

147

150

153

156

159

162

165

168

171

174

177

180

183

186

189

192

195

198

201

204

207

210

213

216

219

222

225

228

231

234

237

240

243

246

249

252

255

258

261

264

267

270

273

276

279

282

285

288

291

294

297

300

303

306

309

312

315

318

321

324

327

330

333

336

339

342

345

348

351

354

357

360

363

366

369

372

375

378

381

384

387

390

393

396

399

402

405

408

411

417

420

423

426

429

432

435

438

441

444

447

450

453

456

459

462

468

474

477

480

483

486

489

492

495

501

504

510

513

516

519

522

525

528

531

537

540

543

546

549

552

555

558

561

564

567

570

573

576

579

582

588

591

597

600

603

606

609

612

624

627

630

633

639

648

654

660

669

675

687

696

699

708

711

720

726

735

738

750

753

765

768

789

792

801

804

813

825

840

843

861

885

900

939

945

954

960

966

1002

1026

1068

1071

1098

1104

1125

1140

1200

1209

1263

1335

1344

1359

1374

1569

1638

1800

1863

1980

2001

2040

2388

2640

3000

3600

4698

5100
Clear
Number of Teeth
30

33

35

36

37

40

41

42

43

44

45

47

48

49

50

51

52

53

54

55

56

57

58

59

60

61

62

63

64

65

66

67

68

69

70

71

72

73

74

75

76

77

78

79

80

81

82

83

84

85

86

87

88

89

90

91

92

93

94

95

96

97

98

99

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

156

158

159

160

161

162

163

164

165

167

168

170

171

172

173

174

175

176

177

179

180

181

182

183

184

185

186

187

188

189

190

191

192

193

194

196

197

199

200

201

202

203

204

208

209

210

211

213

216

218

220

223

225

229

232

233

236

237

240

242

245

246

250

251

255

256

263

264

267

268

271

275

280

281

287

295

300

313

315

318

320

322

334

342

356

357

366

368

375

380

400

403

421

445

448

453

458

523

546

600

621

660

667

680

796

880

1000

1200

1566

1700
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

14 Day(s) or Less
Clear

Specify Alterations

Timing Belts HTD3M (Part Number)

Volume Discount

Check FAQ of this product (7 items)

Brand :

MiSUMi Economy

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Product Description

Timing Belts HTD3M
It is an arc tooth profile that has higher transmission power than the trapezoidal tooth timing belt.
This belt always uses for high torque transmission in an automation machine
[Features]
• Belt Shape: Closed End
• Belt Tooth Type: H3M (arc tooth profile)
• Tooth Pitch: 3 mm.
• Belt Width: 6, 9, 12, and 15 mm.
• Circumference Length Shortest/Longest: 90 mm. and 5100 mm.
• Belt Operating Temperature Range: －10 to 90℃.
• Material:
Tooth rubber: Chloroprene
Core wire: Glass Fiber
Tooth surface protection layer: Nylon canvas
[Applications]
Suitable for use with a timing pulley in a transmission system in an automation machine

Economy HTD 3M Timing Belt

Compact DesignChloroprene MaterialReinforced Core

- With a smaller tooth pitch and a wide range of compact sizes, our HTD 3M belts are perfect for applications with limited space.

- Constructed with high-quality chloroprene rubber, these belts excel in resisting abrasion, oil, and grease, ensuring extended service life even in demanding environments.

- The glass fiber reinforced core provides exceptional strength and tensile strength, preventing belt elongation and slippage, resulting in consistent power transmission.

- Engineered to function reliably in temperatures ranging from -10°C to 90°C, these belts offer versatility across various operating conditions.

- Reduced Vibration and Noise for Smooth Operation. The arc tooth profile contributes to minimal vibration and noise generation, creating a smoother and quieter operation.

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Timing Belt Product Overview

Usually, timing pulleys and Timing Belt are widely used to design mechanisms for transmitting rotational power generated by motors.
Driving and transmission are realized through the engagement between the teeth of timing pulleys and Timing Belts.
Local production in China delivers MISUMI quality at low price.

Timing Belt Product Features

■ HTD type arc tooth profile rubber Timing Belt (H3M/H5M)
Feature 1: The arc tooth profile has higher transmission power in comparison with the trapezoidal tooth.
Feature 2: Economical and maintenance free.
Feature 3: The tooth rubber adopts chloroprene to protect core wire from dirt, grease, and wet environments.
Feature 4:·Have certain conductivity.
Feature 5:·Recommended Operating Temperature Range: -10 to 90℃.

Timing Belt Dimensional Drawing

Dimensional drawing of MISUMI Economy series product belt

Timing Belt Specifications Overview

■Timing Belt Material/Specification Table

Material
① Rear rubber	Chloroprene
② Tooth rubber	Chloroprene
③ Core wire	Glass Fiber
④ Backing cloth	Nylon canvas

Types	Tooth pitch	Lr	H	h	PLD
H3M	3	1.78	2.4	1.17	0.381

Belt circumference length is core wire length.

Belt Operating Temperature Range: －10 to 90℃.

The model engraved on the back of the product is the manufacturer model.

MISUMI makes no commitment to this product brand.

For the transmission capacity and calculation and design method of economy series Timing Belt, please refer to the national standard (GB) design manual.

Example of Timing Belt Use

Timing Belt Usage Method Example Drawing	Instructions for use of timing wheel and Timing Belt
	①Driving (The driven wheel is driven by the driving wheel for transmission)
	②Transmission (Used for repeated motion with the object not rotating and high requirements on positioning accuracy)

Timing Belt Usage Method Example Drawing	Instructions for use of timing wheel and Timing Belt
	③Conveyance (Plates are conveyed by two timing toothed belts)
	④Traction transmission (Workpieces are clamped and transmitted by the belt)

Timing Belt Application Industries

Food	Semiconductor	Smart phone

Automotive	Electronic & Electrical Appliances	Medical

Timing Belt Usage Method

■ Installation method for Timing Belt transmission
①	Turn off the power supply, remove the protective cover, loosen the motor assembly bolts, move the motor so that the belt is loose enough. The belt can be removed without prying. Never try to pry the belt down.
②	Remove the old belt and check for abnormal wear. Excessive wear may mean that there are problems in the design or maintenance of the transmission device.
③	Choose the right belt to replace.
④	To clean the belt and pulley, wipe with a cloth dipped in a small amount of non-volatile liquid. Soaking in detergent or scrubbing the belt with detergent is not advisable. To remove grease, it is also undesirable to wipe with sandpaper or scratch with a sharp object. The belt must be kept dry before installation and use.
⑤	Check the pulley for abnormal wear or cracks. If the wear is excessive, the pulley must be replaced.
⑥	Check whether the pulley is linearly symmetrical. Linear symmetry of the pulley is essential for the operation of the Timing Belt, especially the Timing Belt transmission device. Asymmetry of the pulley is shown as follows:

⑦	Check the remaining transmission device components, such as bearings and bushings, for symmetry, durability, lubrication and other conditions.
⑧	Install a new belt on the pulley. Never pry or use too much force.
⑨	Tighten to narrow the center distance of the transmission device until the tension tester detects that the belt tension is appropriate. Turn the driving wheel several times with your hands. Re-test tension.
⑩	Tighten the assembly bolts of the motor and correct the torque. Since any change in the center distance of the transmission device during operation will result in poor belt performance, it is important to ensure that all transmission components have been tightened.
⑪	Start the device and observe the belt performance to see if there is abnormal vibration, and listen carefully if there is abnormal noise. It is best to turn off the machine and check the conditions of the bearing and motor. If it feels too hot to the touch, the belt may be too tight, the bearing may be asymmetrical, or the lubrication may be incorrect.

Timing Belt Precautions

①Do not bend the Timing Belt by force.
It is strictly forbidden to bend the belt, which easily causes breakage

Do not use in direct contact with water, solvent, oil, acid, alkali, UV, ozone, etc.

③ Please avoid using or keeping at extreme high or low temperatures beyond the operating temperature range, or in humid environments.
④ During installation and maintenance, be sure to cut off the power supply and confirm that the machine is completely stopped before proceeding.
⑤ When there may be impurities, be sure to set the guard.

Timing Belt Related Products

Timing Belts S3M	Timing Belts S5M	Timing Pulleys S3M

Reference model: C-HTBN141S3M-60	Reference model: C-HTBN350S5M-150	Reference model: C-HTPA18S3M100-A-P5

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 60; 90

Part Number
C-HTBN945H3M-90

Part Number	Price	Minimum Order Qty.	Volume Discount	Days to Ship	RoHS	Belt Width (mm) (mm)	Circumference Length (mm)	Number of Teeth
	₹ 727.00	2 Piece(s)	Available	14 Day(s)	10	9	945	315

Dimensional Drawing

MISUMI Complete specifications Factory direct sales Original quality

Specification Table

■Specification Table
■Type H3M (Tooth Pitch: 3mm)

Belt Number	Belt Nominal Width	Number of Teeth	Belt Circumference Length (mm)
90H3M	60 (6mm) 90 (9mm) 120 (12mm) 150 (15mm)	30	90
99H3M		33	99
105H3M		35	105
108H3M		36	108
111H3M		37	111
120H3M		40	120
123H3M		41	123
126H3M		42	126
129H3M		43	129
132H3M		44	132
135H3M		45	135
141H3M		47	141
144H3M		48	144
147H3M		49	147
150H3M		50	150
153H3M		51	153
156H3M		52	156
159H3M		53	159
162H3M		54	162
165H3M		55	165
168H3M		56	168
171H3M		57	171
174H3M		58	174
177H3M		59	177
180H3M		60	180
183H3M		61	183
186H3M		62	186
189H3M		63	189
192H3M		64	192
195H3M		65	195
198H3M		66	198
201H3M		67	201
204H3M		68	204
207H3M		69	207
210H3M		70	210
213H3M		71	213
216H3M		72	216
219H3M		73	219
222H3M		74	222
225H3M		75	225
228H3M		76	228
231H3M		77	231
234H3M		78	234
237H3M		79	237
240H3M		80	240
243H3M		81	243
246H3M		82	246
249H3M		83	249
252H3M		84	252
255H3M		85	255
258H3M		86	258
261H3M		87	261
264H3M		88	264
267H3M		89	267
270H3M		90	270
273H3M		91	273
276H3M		92	276
279H3M		93	279
282H3M		94	282
285H3M		95	285
288H3M		96	288
291H3M		97	291
294H3M		98	294
297H3M		99	297
300H3M	100	300
303H3M	101	303
306H3M	102	306
309H3M	103	309
312H3M	104	312
315H3M	105	315
318H3M	106	318
321H3M	107	321
324H3M	108	324
327H3M	109	327
330H3M	110	330
333H3M	111	333
336H3M	112	336
339H3M	113	339
342H3M	114	342
345H3M	115	345
348H3M	116	348
351H3M	117	351
354H3M	118	354
357H3M	119	357
360H3M	120	360
363H3M	121	363
366H3M	122	366
369H3M	123	369
372H3M	124	372
375H3M	125	375
378H3M	126	378
381H3M	127	381
384H3M	128	384
387H3M	129	387
390H3M	130	390
393H3M	131	393
396H3M	132	396
399H3M	133	399
402H3M	134	402
405H3M	135	405
408H3M	136	408
411H3M	137	411
417H3M	139	417
420H3M	140	420
423H3M	141	423
426H3M	142	426
429H3M	143	429
432H3M	144	432
435H3M	145	435
438H3M	146	438
441H3M	147	441
444H3M	148	444
447H3M	149	447
450H3M	150	450

Belt Number	Belt Nominal Width	Number of Teeth	Belt Circumference Length (mm)
453H3M	60 (6mm) 90 (9mm) 120 (12mm) 150 (15mm)	151	453
456H3M		152	456
459H3M		153	459
462H3M		154	462
468H3M		156	468
474H3M		158	474
477H3M		159	477
480H3M		160	480
483H3M		161	483
486H3M		162	486
489H3M		163	489
492H3M		164	492
495H3M		165	495
501H3M		167	501
504H3M		168	504
510H3M		170	510
513H3M		171	513
516H3M		172	516
519H3M		173	519
522H3M		174	522
525H3M		175	525
528H3M		176	528
531H3M		177	531
537H3M		179	537
540H3M		180	540
543H3M		181	543
546H3M		182	546
549H3M		183	549
552H3M		184	552
555H3M		185	555
558H3M		186	558
561H3M		187	561
564H3M		188	564
567H3M		189	567
570H3M		190	570
573H3M		191	573
576H3M		192	576
579H3M		193	579
582H3M		194	582
588H3M		196	588
591H3M		197	591
597H3M		199	597
600H3M		200	600
603H3M		201	603
606H3M		202	606
609H3M		203	609
612H3M		204	612
624H3M		208	624
627H3M		209	627
630H3M		210	630
633H3M		211	633
639H3M		213	639
648H3M		216	648
654H3M		218	654
660H3M		220	660
669H3M		223	669
675H3M		225	675
687H3M		229	687
696H3M		232	696
699H3M		233	699
708H3M		236	708
711H3M		237	711
720H3M		240	720
726H3M		242	726
735H3M	245	735
738H3M	246	738
750H3M	250	750
753H3M	251	753
765H3M	255	765
768H3M	256	768
789H3M	263	789
792H3M	264	792
801H3M	267	801
804H3M	268	804
813H3M	271	813
825H3M	275	825
840H3M	280	840
843H3M	281	843
861H3M	287	861
885H3M	295	885
900H3M	300	900
939H3M	313	939
945H3M	315	945
954H3M	318	954
960H3M	320	960
966H3M	322	966
1002H3M	334	1002
1026H3M	342	1026
1068H3M	356	1068
1071H3M	357	1071
1098H3M	366	1098
1104H3M	368	1104
1125H3M	375	1125
1140H3M	380	1140
1200H3M	400	1200
1209H3M	403	1209
1263H3M	421	1263
1335H3M	445	1335
1344H3M	448	1344
1359H3M	453	1359
1374H3M	458	1374
1569H3M	523	1569
1638H3M	546	1638
1800H3M	600	1800
1863H3M	621	1863
1980H3M	660	1980
2001H3M	667	2001
2040H3M	680	2040
2388H3M	796	2388
2640H3M	880	2640
3000H3M	1000	3000
3600H3M	1200	3600
4698H3M	1566	4698
5100H3M	1700	5100

Basic Information

Belt Type	3M	Belt Shape	Closed End	Belt Material	Rubber Belt
Belt Tooth Surface	Standard (Single Sided)	Core Wire Material	Glass Fiber	Belt Shape Type	Circular Tooth Profile HTD Belt
Transmission Torque	High Torque Transmission

Please check the type/dimensions/specifications of the part C-HTBN945H3M-90 in the Timing Belts HTD3M series.

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: Why is the order model of the timing belt inconsistent with the actual belt label and engraving?: Answer: Order model is MISUMI product model, the label on the belt or printed model on the belt surface is the belt manufacturer model, which varies with manufacturer, but there will be no influence on the product itself.
Question: The timing belt has been broken after use for a very short period of time. Is there a problem with the quality of the belt?: Answer:
The timing belt is a standard product, and the same batch of products have very few individual quality problems, please refer to 【Main causes of premature breakage and corresponding countermeasures】to troubleshoot the equipment in use.
Question: Can alteration be made to the timing belt?: Answer: Alteration cannot be made to the circumference of the timing belt, and partial alteration can be made to the width.
Question: What kind of belt is better to use under conditions that require high cleanliness?: Answer: The use of urethane belts is recommended, which has significantly improved dust drop, compared to the rubber belt.
Question: What are the two main types of timing belts according to their functions? What is the role?: Answer: Timing belts are mainly divided into transmission type and driving type. For transmission type, the load can be placed on the timing belt surface for transmission. For driving type, no load is carried, and only the role of transmitting torque is played, which is similar to the role of chain.
Question: How to judge or measure whether the belt tension meets the installation requirements?: Answer: It is recommended that the customer purchase the tension meter by himself and make a judgment according to the calculation formula of the initial design.
Question: Which tooth type of the timing belt has the smallest clearance? What will it affect?: Answer: The arc tooth type has minimum clearance, which can improve such indicators as positioning accuracy and rigidity.

Check other FAQ (4 items) Hide

Product variants

Part Number
C-HTBN1002H3M-90
C-HTBN1026H3M-120
C-HTBN1026H3M-150
C-HTBN954H3M-120
C-HTBN954H3M-150
C-HTBN954H3M-60

Standard Unit Price	Minimum order quantity	Volume Discount	Days to Ship	RoHS	Belt Width (mm) (mm)	Circumference Length (mm)	Number of Teeth
₹ 743.00	2 Piece(s)	Available	14 Day(s)	10	9	1002	334
₹ 836.00	2 Piece(s)	Available	14 Day(s)	10	12	1026	342
₹ 923.00	2 Piece(s)	Available	14 Day(s)	10	15	1026	342
₹ 812.00	2 Piece(s)	Available	14 Day(s)	10	12	954	318
₹ 896.00	2 Piece(s)	Available	14 Day(s)	10	15	954	318
₹ 648.00	2 Piece(s)	Available	14 Day(s)	10	6	954	318

Search by Category / Brand

Search by Category

How can we improve?