What brand is the linear bearing of FA?

The linear bearing of FA is MISUMI brand.

Is there a product stamp on the linear bearing?

There is no stamp on the product body, and the product model is on the packaging box.

How is linear bearing maintained regularly?

MISUMI recommends that linear bearing is regularly replenished with grease, and it is recommended to do so once every six months. When the moving distance is long, it is recommended to move once every three months or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.

Comparison of antirust ability of linear bearings?

Antirust ability from strong to weak: No-Electro Nickel Plated → No Surface Treatment. Standard grade bearing steel is easy to rust, so it is necessary to apply anti-rust oil regularly.

What is the difference between the single liner type and the double liner type of linear bearing of FA?

Single liner type is one row of steel balls, and double liner type is two rows of steel balls. Generally, the length of the double liner type is more than twice that of the single liner type, and the contact area of steel balls is longer, the radial sway is smaller, and the rated load is larger.

When the linear bearing and the guide shaft are used together, some are closely matched, but some have relatively large clearance. Does it affect the use?

The linear bearing and the guide shaft are in point contact and rolling fit through the circulating steel ball structure. Because of point contact and non-interference fit, it is normal to have clearance between the shaft and the bearing, which will not affect the use. The use of this structure greatly reduces the friction resistance and prolongs the service life of the workpiece.

How to deal with oil leakage in the received linear bearing?

Linear bearing is coated with anti-rust oil (except for MX grease device) when leaving the factory, which has little influence on grease. It is recommended to clean it before use and apply grease after drying.

Can the linear bearing rotate?

The linear bearing is not suitable for rotating motion in structure. If it is forcibly rotated, it may cause damage to the product. If rotating motion is required, please give priority to linear type rotating bushings.

Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(1 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

E-LBF6LUU

No. type Inscribed Circle Dia. dr Overall Length L Outer Cylinder Surface Treatment Outer Dia. D Ball Recirculating Type Length Eccentricity Style of Mounting Hole CAD Days to Ship

Specification/Dimensions

No.
None
Clear
type
- C-LBFM
- C-LMF
- E-LBF
- E-LBFL
- E-LBFM
- E-LBFZ
Clear
Inscribed Circle Dia. dr(Ø)
5

6

8

10

12

13

16

20

25

30

35

40

50
Clear
Overall Length L(mm)
15

19

24

28

29

30

32

35

37

42

45

55

57

59

61

64

70

80

100

112

123

135

151

192
Clear
Outer Cylinder Surface Treatment
- No Surface Treatment
- Surface Treatment
  - Electroless Nickel Plating
Clear
Outer Dia. D(Ø)
10

12

15

19

21

23

28

32

40

45

52

60

80
Clear
Ball Recirculating Type
- Single
- Double
Clear
Length
- Single
- Double
Clear
Eccentricity(µm)
0.02

0.024

0.028

0.03

0.04

0.045

24

30

40
Clear
Style of Mounting Hole
- Opposite Couterbored Hole
- Standard Counterbored Hole
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

Same day

15 Day(s) or Less
Clear

Specify Alterations

Round Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole (E-LBF6LUU)

Volume Discount

Check FAQ of this product (8 items)

Brand :

MiSUMi Economy

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Product Description

New at MISUMI? Get 20% Discount on your First Purchase. Click to Register Now

Round Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole
These Linear Bushings are an economy item, The price is cheaper than the MISUMI standard product.They offer a wide variety of sizes to choose from.
[Features]
● Support Shaft Diameter Minimum/Maximum (mm.): 6 and 50
● Overall Length Minimum/Maximum (mm.): 19 and 192
● Shape : Round Flanged
● Ball Recirculating Type : Single or Double
● Material:
- Housing - SUJ2 Equivalent
- Ball - SUJ2 Equivalent
[Application]
It is used in industrial machinery such as conveyor systems, packaging machines, and robotic equipment.

Economy Round Flanged Linear Bushing

Flanged Versatile Secure

- Versatile round flanged bushing for secure mounting.

- Available with single and double ball recirculating options.

- Supports a wide range of shaft diameters

- Optional electroless nickel plating for superior rust resistance.

- Ideal for conveyor systems and precision equipment.

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product Overview

The flanged linear bearing integrates the linear bearing with the support, which is compact in structure and easy to assemble to the mechanism accurately and simply.

Linear bearing is a linear type motion guiding mechanism matched with linear guide shaft. The steel ball rolls circularly along the track groove formed by the shell and the retainer, and the linear bearing reciprocates linearly relative to the guide shaft.
Through the rolling of steel ball, high-efficiency movement with low friction resistance can be realized.

Dimensional Drawing

The flange of this product is not heat treated and may be scratched.

■ Material

Counterbored	Type	Case			Ball	Retainer	Ambient Operating temperature	Accessories: Seal
		Material	Hardness	Surface Treatment	Material	Material		Material
Opposite counterbored	E-LBFZ	Equivalent to SUJ2	58HRC～	－	Equivalent to SUJ2	Resin	-20~80℃	Nitrile Rubber
Standard	E-LBF
	E-LBFM			Electroless Nickel Plating

For the opposite counterbored type, the product can be mounted from the reverse side.

Resin retainers are available in black and yellow, with the same performance. Please feel free to use.

Specification Table

		Part Number (Type ・Diameter of Inscribed Circle dr ・Ball Retainer)
		E-LBF8UU E-LBFM20LUU

Part Number				O.D. D Tolerance					Overall Length L			H	T	d	d₁
Type	dr	Tolerance	Length Type		Single No Surface Treatment	Double No Surface Treatment	Single With Surface Treatment	Double With Surface Treatment	Single	Double	Tolerance
E－LBFZ E－LBF E－LBFM	6	＋0.003 －0.013	UU (Single) LUU (Double)	12	0 －0.015	0 －0.016	0 －0.015	0 －0.015	19	35	±0.3	28	5	3.5	6
	8			15					24	45		32
	10			19		0 －0.018	0 －0.018	0 －0.018	29	55	±0.6	40	6	4.5	7.5
	12			21	0 －0.018				30	57		42
	13			23					32	61		43
	16			28					37	70		48
	20	＋0.003 －0.015		32	0 －0.021	0 －0.021	0 －0.021	0 －0.021	42	80		54	8	5.5	9
	25			40					59	112		62
	30			45					64	123		74	10	6.6	11
E－LBF E－LBFM	35	＋0.003 －0.016		52	0 －0.028	0 －0.03	0 －0.025	0 －0.028	70	135		82
	40			60					80	151		96	13	9	14
	50			80	0 －0.03	0 －0.032	0 －0.028	0 －0.03	100	192		116

Internal connector diameter dr	t	P.C.D.	Eccentricity		Rows of balls	Perpendicularity		Basic Load Rating C (Dynamic) N		Basic Load Rating Co (Static) N		Mass（g）		Double Type Allowable Static Moment （N·m）
Internal connector diameter dr	t	P.C.D.	Single	Double	Rows of balls	Single	Double	Single	Double	Single	Double	Single	Double	Double Type Allowable Static Moment （N·m）
6	3.1	20	0.024	0.028	4	0.024	0.028	206	324	265	529	24	31	2.18
8	3.1	24		0.028			0.028	265	431	380	784	37	51	4.31
10	4.1	29		0.03			0.03	372	588	549	1100	72	98	7.24
12		32						412	657	598	1200	76	110	10.9
13		33						510	813	784	1570	88	130	11.6
16		38			5			775	1230	1180	2350	120	190	19.7
20	5.1	43	0.03	0.04	5	0.03	0.04	882	1400	1370	2740	180	260	26.8
25	5.1	51			6			980	1560	1570	3140	340	540	43.4
30	6.1	60						1570	2490	2740	5490	470	680	82.8
35	6.1	67	0.04	0.045		0.04	0.045	1670	2650	3140	6270	650	1020	110
40	8.1	78						2160	3430	4020	8040	1060	1570	147
50	8.1	98						3820	6080	7940	15900	2200	3600	397

Usage Method

Product Drawings	Instructions for use
	When the linear bearing is under heavy load (unbalanced load), one piece of single liner type is not applicable. It is recommended to use one piece of double liner type or multiple pieces of single liner type.
	Linear bearing is not suitable for rotating motion in structure. If you rotate forcibly, it may cause damage to the product. Please pay attention during use.
	Linear bearing is not suitable for repeated plugging and unplugging.
	When inserting the guide shaft into the linear bearing, please align the center and insert it slowly, otherwise the steel ball will fall off or the retainer will be deformed.

Precautions

■ Regular maintenance:
① Before use, please apply grease to the ball row inside the linear bearing, and then replenish it in due course. Grease forms an oil film on the surfaces of steel ball and rolling surface (guide shaft·bushing) of linear bearing, which effectively reduces friction and prevents sintering. Grease reduction and aging will greatly affect the life of linear bearing.
② Recommended grease: lithium soap grease.
③ Recommended grease filling interval: Usually every 6 months.
④When the moving distance is long, it is recommended to move once every three months or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.
⑤ When the linear bearing is subjected to large moment load (eccentric load), one piece of single liner type is not applicable, so it is recommended to use one piece of double liner type or multiple pieces of single liner type.

■ Dust prevention measures:
If dust or foreign matter enters the inside of the linear bearing, it may damage the circulation of steel balls, resulting in unexpected failures. When used in harsh environment, please install dust cover and protection cover, etc.

■ MISUMI linear bearing is recommended to be combined with guide shaft with quenching g6 tolerance.

■ MISUMI linear bearing is recommended to be installed on the holder with H7 tolerance. The linear bearing is in clearance fit with the holder.

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 45; 60

Part Number
E-LBF6LUU

Part Number	Price	Minimum Order Qty.	Volume Discount	Days to Ship	RoHS	Inscribed Circle Dia. dr (Ø)	Overall Length L (mm)	Outer Cylinder Surface Treatment	Outer Dia. D (Ø)	Ball Recirculating Type	Length	Eccentricity (µm)	Basic Load Rating: Dynamic Load (Details) (N)	Basic Load Rating: Static Load (N)	Inscribed Circle Dia. Tolerance (Negative Side) (mm)	No.	Style of Mounting Hole
	₹ 728.00	1 Piece(s)	Available	Same day	10	6	35	No Surface Treatment	12	Double	Double	0.028	324	529	-0.016	-	Standard Counterbored Hole

■ Test conditions
• Linear bearing (inner diameter 16) is matched with MISUMI guide shaft (PSFJ) to apply 63kg load and walk for 30km, and confirm the product damage and sliding noise.
Product Feature Drawings

■ Test results
The economy series product ensures smooth sliding of steel ball, which have good durability and low noise
Product Feature Drawings

*Products circulating on the market are similar products randomly purchased by our company from online or offline markets
*The test data are obtained through testing by our company, which are for reference only

Example of Use

Equipment Name:
Conveying direction change mechanism

Design Purpose:
The conveying direction of the workpiece conveyed by the conveyor belt is 90°. Change the direction to move.

Parts Application Description:
By matching with the air cylinder, the conveying direction of the workpiece can be changed.

Application Industries

Electronic & Electrical Appliances	Automotive	Lithium battery

LCD	Smart phone	Semiconductor

Basic Information

Type	Flange	Flange Type	Standard Flange	Style	Standard
Outer Cylinder Material	SUJ2 Equivalent	Lubrication Type	Not Provided	Accuracy	Standard Grade
Motion	Linear	Types	Standard Flange	Ball Material	SUJ2 Equivalent
Retainer Material	Plastic	Seal	Provided	Greased Filled	Not Provided

Please check the type/dimensions/specifications of the part E-LBF6LUU in the Round Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole series.

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: What brand is the linear bearing of FA?: Answer: The linear bearing of FA is MISUMI brand.
Question: Is there a product stamp on the linear bearing?: Answer: There is no stamp on the product body, and the product model is on the packaging box.
Question: How is linear bearing maintained regularly?: Answer: MISUMI recommends that linear bearing is regularly replenished with grease, and it is recommended to do so once every six months. When the moving distance is long, it is recommended to move once every three months or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.
Question: Comparison of antirust ability of linear bearings?: Answer: Antirust ability from strong to weak: No-Electro Nickel Plated → No Surface Treatment.
Standard grade bearing steel is easy to rust, so it is necessary to apply anti-rust oil regularly.
Question: What is the difference between the single liner type and the double liner type of linear bearing of FA?: Answer: Single liner type is one row of steel balls, and double liner type is two rows of steel balls. Generally, the length of the double liner type is more than twice that of the single liner type, and the contact area of steel balls is longer, the radial sway is smaller, and the rated load is larger.
Question: When the linear bearing and the guide shaft are used together, some are closely matched, but some have relatively large clearance. Does it affect the use?: Answer: The linear bearing and the guide shaft are in point contact and rolling fit through the circulating steel ball structure. Because of point contact and non-interference fit, it is normal to have clearance between the shaft and the bearing, which will not affect the use. The use of this structure greatly reduces the friction resistance and prolongs the service life of the workpiece.
Question: How to deal with oil leakage in the received linear bearing?: Answer: Linear bearing is coated with anti-rust oil (except for MX grease device) when leaving the factory, which has little influence on grease. It is recommended to clean it before use and apply grease after drying.
Question: Can the linear bearing rotate?: Answer: The linear bearing is not suitable for rotating motion in structure. If it is forcibly rotated, it may cause damage to the product. If rotating motion is required, please give priority to linear type rotating bushings.

Check other FAQ (5 items) Hide

Product variants

Part Number
C-LMF20UU
C-LMF25UU
C-LMF30UU
E-LBF6UU
E-LBF8LUU
E-LBF8UU

Standard Unit Price	Minimum order quantity	Volume Discount	Days to Ship	RoHS	Inscribed Circle Dia. dr (Ø)	Overall Length L (mm)	Outer Cylinder Surface Treatment	Outer Dia. D (Ø)	Ball Recirculating Type	Length	Eccentricity (µm)	Basic Load Rating: Dynamic Load (Details) (N)	Basic Load Rating: Static Load (N)	Inscribed Circle Dia. Tolerance (Negative Side) (mm)	No.	Style of Mounting Hole
₹ 356.00	1 Piece(s)	Available	Same day Stock	10	20	42	No Surface Treatment	32	Single	Single	30	882	1370	-0.013	None	-
₹ 488.71	1 Piece(s)	Available	Same day Stock	10	25	59	No Surface Treatment	40	Single	Single	30	980	1570	-0.013	None	-
₹ 610.00	1 Piece(s)	Available	Same day Stock	10	30	64	No Surface Treatment	45	Single	Single	30	1570	2740	-0.013	None	-
₹ 454.00	1 Piece(s)	Available	15 Day(s)	10	6	19	No Surface Treatment	12	Single	Single	24	206	265	-0.015	-	Standard Counterbored Hole
₹ 728.00	1 Piece(s)	Available	Same day Stock	10	8	45	No Surface Treatment	15	Double	Double	0.028	431	784	-0.016	-	Standard Counterbored Hole
₹ 460.00	1 Piece(s)	Available	15 Day(s)	10	8	24	No Surface Treatment	15	Single	Single	24	265	380	-0.015	-	Standard Counterbored Hole

Guide shaft Straight bar type	(Economy series) Linear bearing Standard type Single liner type	Shaft Collar Slit

Typical model: SFJ20-75	Typical model: C-LM8UU	Typical model: SCS8-10

Search by Category / Brand

Search by Category

How can we improve?