What brand is the linear bearing of FA?

The linear bearing of FA is MISUMI brand.

Is there a product stamp on the linear bearing?

There is no stamp on the product body, and the product model is on the packaging box.

How is linear bearing maintained regularly?

MISUMI recommends that linear bearing is regularly replenished with grease, and it is recommended to do so once every six months. When the moving distance is long, it is recommended to move once every three months or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.

Comparison of antirust ability of linear bearings?

Antirust ability from strong to weak: No-Electro Nickel Plated → No Surface Treatment. Standard grade bearing steel is easy to rust, so it is necessary to apply anti-rust oil regularly.

What is the difference between the single liner type and the double liner type of linear bearing of FA?

Single liner type is one row of steel balls, and double liner type is two rows of steel balls. Generally, the length of the double liner type is more than twice that of the single liner type, and the contact area of steel balls is longer, the radial sway is smaller, and the rated load is larger.

When the linear bearing and the guide shaft are used together, some are closely matched, but some have relatively large clearance. Does it affect the use?

The linear bearing and the guide shaft are in point contact and rolling fit through the circulating steel ball structure. Because of point contact and non-interference fit, it is normal to have clearance between the shaft and the bearing, which will not affect the use. The use of this structure greatly reduces the friction resistance and prolongs the service life of the workpiece.

How to deal with oil leakage in the received linear bearing?

Linear bearing is coated with anti-rust oil (except for MX grease device) when leaving the factory, which has little influence on grease. It is recommended to clean it before use and apply grease after drying.

Can the linear bearing rotate?

The linear bearing is not suitable for rotating motion in structure. If it is forcibly rotated, it may cause damage to the product. If rotating motion is required, please give priority to linear type rotating bushings.

Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(1 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

E-LBF30LUU

No. Holder Material type Inscribed Circle Dia. dr Overall Length L Outer Cylinder Surface Treatment Outer Dia. D Ball Recirculating Type Length Eccentricity Style of Mounting Hole CAD Days to Ship

Specification/Dimensions

No.
None
Clear
Holder Material
- Opposite Counterbored Hole
- Standard
Clear
type
- C-LBFM
- C-LMF
- E-LBF
- E-LBFL
- E-LBFM
- E-LBFZ
Clear
Inscribed Circle Dia. dr(Ø)
6

8

10

12

13

16

20

25

30

35

40

50
Clear
Overall Length L(mm)
19

24

29

30

32

35

37

42

45

55

57

59

61

64

70

80

100

112

123

135

151

192
Clear
Outer Cylinder Surface Treatment
- No Surface Treatment
- Surface Treatment
  - Electroless Nickel Plating
Clear
Outer Dia. D(Ø)
12

15

19

21

23

28

32

40

45

52

60

80
Clear
Ball Recirculating Type
- Single
- Double
Clear
Length
- Single
- Double
Clear
Eccentricity(µm)
0.024

0.028

0.03

0.04

0.045

24

30

40
Clear
Style of Mounting Hole
- Opposite Couterbored Hole
- Standard Counterbored Hole
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

Same day

15 Day(s) or Less
Clear

Specify Alterations

Round Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole (E-LBF30LUU)

Volume Discount

Check FAQ of this product (8 items)

Brand :

MiSUMi Economy

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Product Description

Round Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole
These Linear Bushings are an economy item, The price is cheaper than the MISUMI standard product.They offer a wide variety of sizes to choose from.
[Features]
● Support Shaft Diameter Minimum/Maximum (mm.): 6 and 50
● Overall Length Minimum/Maximum (mm.): 19 and 192
● Shape : Round Flanged
● Ball Recirculating Type : Single or Double
● Material:
- Housing - SUJ2 Equivalent
- Ball - SUJ2 Equivalent
[Application]
It is used in industrial machinery such as conveyor systems, packaging machines, and robotic equipment.

Economy Round Flanged Linear Bushing

Flanged Versatile Secure

- Versatile round flanged bushing for secure mounting.

- Available with single and double ball recirculating options.

- Supports a wide range of shaft diameters

- Optional electroless nickel plating for superior rust resistance.

- Ideal for conveyor systems and precision equipment.

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product Overview

The flanged linear bearing integrates the linear bearing with the support, which is compact in structure and easy to assemble to the mechanism accurately and simply.

Linear bearing is a linear type motion guiding mechanism matched with linear guide shaft. The steel ball rolls circularly along the track groove formed by the shell and the retainer, and the linear bearing reciprocates linearly relative to the guide shaft.
Through the rolling of steel ball, high-efficiency movement with low friction resistance can be realized.

■Dimensional Drawing

This product is delivered at the initial stage, the color of the packing may be inconsistent with the photo, which shall be subject to the actual product.

The flange part of this product is not heat-treated, and there may be bumps and bruises.

Material

Type	dr [Φ:mm]	Housing			Ball	Retainer	Operating environment temperature	Accessories
		Material	Hardness	Surface Treatment	Material	Material
C-LMF_UU	6~30	Equivalent to SUJ2	58HRC～	－	Equivalent to SUJ2	Resin	-20~80℃	Seal packing Material Nitrile Rubber
E-LBF	6~50
E-LBFM	6~50			Electroless Nickel Plating
E-LBFZ	6~30			－

If there are requirements for rust prevention, give priority to products with surface treatment of electroless nickel plating or those with low temperature hard chromium plating.

Specification

		Part Number (Type ・Diameter of Inscribed Circle dr ・Ball Retainer)
		C-LMF8UU E-LBF8UU E-LBFM20LUU

■ Dimension Specification Table

Part Number				O.D. D Tolerance					Total Length: L			H	T	d	d1	t	P.C.D.	Eccentricity (Max.)		Number of ball rows	Verticality		Weight (g)		Basic Rated Load Single UU		Basic Rated Load Double LUU		Double Type Allowable Static Moment (N・m)
Type	dr	Ball Retainer (Length)	Tolerance		E-LBF_UU E-LBFZ_UU	E-LBF_LUU E-LBFZ_LUU	E-LBFM_UU	E-LBFM_LUU	Single UU	Double LUU	Tolerance							Single UU	Double LUU		Single UU	Double LUU	Single	Double	C (Dynamic) N	Co (Static) N	C (Dynamic) N	Co (Static) N
E-LBFZ (Opposite Counterbored) E-LBF (No Surface Treatment) E-LBFM (Electroless Nickel Plating)	6	UU (Single) LUU (Double)	+0.003 -0.012	12	0 -0.015	0 -0.016	0 -0.015	0 -0.015	19	35	±0.3	28	5	3.5	6	3.1	20	0.024	0.028	4	0.024	0.028	24	31	206	265	324	529	2.18
	8			15					24	45	±0.6	32					24						37	51	265	380	431	784	4.31
	10			19		0 -0.018			29	55		40	6	4.5	7.5	4.1	29		0.03			0.03	72	98	372	549	588	1100	7.24
	12			21	0 -0.018		0 -0.018	0 -0.018	30	57		42					32						76	110	412	598	657	1200	10.9
	13			23					32	61		43					33						88	130	510	784	813	1570	11.6
	16			28					37	61		48					38			5			120	190	775	1180	1230	2350	19.7
	20		+0.003 -0.013	32	0 -0.021	0 -0.021	0 -0.021	0 -0.021	42	70		54	8	5.5	9	5.1	43	0.03	0.04		0.03	0.04	180	260	882	1370	1400	2740	26.8
	25			40					59	80		62					51			6			340	540	980	1570	1560	3140	43.4
	30			45					64	112		74	10	6.6	11	6.1	60						470	680	1570	2740	2490	5490	82.8
E-LBF (No Surface Treatment) E-LBFM (Electroless Nickel Plating)	35		+0.003 -0.014	52	0 -0.028	-0.03	0 -0.025	0 -0.028	70	135		82					67	0.03	0.045		0.04	0.045	650	1020	1670	3140	2650	6270	110
	40			60					80	151		96	13	9	14	8.1	78						1060	1570	2160	4020	3430	8040	147
	50		+0.003 -0.015	80	0 -0.03	0 -0.032	0 -0.028	0 -0.03	100	192		116					98						2200	3600	3820	7940	6080	15900	397

If there are requirements for rust prevention, give priority to products with surface treatment of electroless nickel plating

Specification of "E-LBF" corresponds to the spec of "C-LMF". Difference between these 2 type is only Part No.

■ Dimension Specification Table

Part Number			Outer Diameter: D		Total Length: L		H	T	d	d1	t	P.C.D.	Eccentricity (Max.)	Number of ball rows	Verticality	Weight (g)	Basic Rated Load
Type	dr	Tolerance		Tolerance		Tolerance											C (Dynamic) N	Co (Static) N
C-LMF_UU	6	+0.003 -0.012	12	0 -0.015	19	±0.6	28	5	3.5	6	3.1	20	0.024	4	0.024	22	206	265
	8		15		24		32					24				32	265	380
	10		19		29		40	6	4.5	7.5	4.1	29				61	372	549
	12		21	0 -0.018	30		42					32				67	412	598
	16		28		37		48					38		5		121	775	1180
	20	+0.003 -0.013	32	0 -0.021	42		54	8	5.5	9	5.1	43	0.03		0.030	162	882	1370
	25		40		59		62					51		6		303	980	1570
	30		45		64		74	10	6.6	11	6.1	60				414	1570	2740

Usage Method

Product Drawings	Instructions for use
	When the linear bearing is under heavy load (unbalanced load), one piece of single liner type is not applicable. It is recommended to use one piece of double liner type or multiple pieces of single liner type.
	Linear bearing is not suitable for rotating motion in structure. If you rotate forcibly, it may cause damage to the product. Please pay attention during use.
	Linear bearing is not suitable for repeated plugging and unplugging.
	When inserting the guide shaft into the linear bearing, please align the center and insert it slowly, otherwise the steel ball will fall off or the retainer will be deformed.

Precautions

■ Regular maintenance:
① Before use, please apply grease to the ball row inside the linear bearing, and then replenish it in due course. Grease forms an oil film on the surfaces of steel ball and rolling surface (guide shaft·bushing) of linear bearing, which effectively reduces friction and prevents sintering. Grease reduction and aging will greatly affect the life of linear bearing.
② Recommended grease: lithium soap grease.
③ Recommended grease filling interval: Usually every 6 months.
④When the moving distance is long, it is recommended to move once every three months or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.
⑤ When the linear bearing is subjected to large moment load (eccentric load), one piece of single liner type is not applicable, so it is recommended to use one piece of double liner type or multiple pieces of single liner type.

■ Dust prevention measures:
If dust or foreign matter enters the inside of the linear bearing, it may damage the circulation of steel balls, resulting in unexpected failures. When used in harsh environment, please install dust cover and protection cover, etc.

■ MISUMI linear bearing is recommended to be combined with guide shaft with quenching g6 tolerance.

■ MISUMI linear bearing is recommended to be installed on the holder with H7 tolerance. The linear bearing is in clearance fit with the holder.

Related Products

Guide shaft Straight bar type	(Economy series) Linear bearing Standard type Single liner type	Shaft Collar Slit

Typical model: SFJ20-75	Typical model: C-LM8UU	Typical model: SCS8-10

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 45; 60

Part Number
E-LBF30LUU

Part Number	Price	Minimum Order Qty.	Volume Discount	Days to Ship	RoHS	Inscribed Circle Dia. dr (Ø)	Overall Length L (mm)	Outer Cylinder Surface Treatment	Outer Dia. D (Ø)	Ball Recirculating Type	Length	Eccentricity (µm)	Basic Load Rating: Dynamic Load (Details) (N)	Basic Load Rating: Static Load (N)	Inscribed Circle Dia. Tolerance (Negative Side) (mm)	No.	Holder Material	Style of Mounting Hole
	₹ 1,062.00	1 Piece(s)	Available	15 Day(s)	10	30	123	No Surface Treatment	45	Double	Double	40	2490	5490	-0.021	-	-	Standard Counterbored Hole

■ Test conditions
• Linear bearing (inner diameter 16) is matched with MISUMI guide shaft (PSFJ) to apply 63kg load and walk for 30km, and confirm the product damage and sliding noise.
Product Feature Drawings

■ Test results
The economy series product ensures smooth sliding of steel ball, which have good durability and low noise
Product Feature Drawings

*Products circulating on the market are similar products randomly purchased by our company from online or offline markets
*The test data are obtained through testing by our company, which are for reference only

Example of Use

Equipment Name:
Conveying direction change mechanism

Design Purpose:
The conveying direction of the workpiece conveyed by the conveyor belt is 90°. Change the direction to move.

Parts Application Description:
By matching with the air cylinder, the conveying direction of the workpiece can be changed.

Application Industries

Electronic & Electrical Appliances	Automotive	Lithium battery

LCD	Smart phone	Semiconductor

Basic Information

Type	Flange	Flange Type	Standard Flange	Style	Standard
Outer Cylinder Material	SUJ2 Equivalent	Lubrication Type	Not Provided	Accuracy	Standard Grade
Motion	Linear	Types	Standard Flange	Flange Shape	Round Flange
Ball Material	SUJ2 Equivalent	Retainer Material	Plastic	Seal	Provided
Greased Filled	Not Provided

Please check the type/dimensions/specifications of the part E-LBF30LUU in the Round Flanged Linear Bushings, Single / Double / Opposite Counterbored Hole series.

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: What brand is the linear bearing of FA?: Answer: The linear bearing of FA is MISUMI brand.
Question: Is there a product stamp on the linear bearing?: Answer: There is no stamp on the product body, and the product model is on the packaging box.
Question: How is linear bearing maintained regularly?: Answer: MISUMI recommends that linear bearing is regularly replenished with grease, and it is recommended to do so once every six months. When the moving distance is long, it is recommended to move once every three months or when the moving distance exceeds 1000km within the time limit, the 1000km shall prevail.
Question: Comparison of antirust ability of linear bearings?: Answer: Antirust ability from strong to weak: No-Electro Nickel Plated → No Surface Treatment.
Standard grade bearing steel is easy to rust, so it is necessary to apply anti-rust oil regularly.
Question: What is the difference between the single liner type and the double liner type of linear bearing of FA?: Answer: Single liner type is one row of steel balls, and double liner type is two rows of steel balls. Generally, the length of the double liner type is more than twice that of the single liner type, and the contact area of steel balls is longer, the radial sway is smaller, and the rated load is larger.
Question: When the linear bearing and the guide shaft are used together, some are closely matched, but some have relatively large clearance. Does it affect the use?: Answer: The linear bearing and the guide shaft are in point contact and rolling fit through the circulating steel ball structure. Because of point contact and non-interference fit, it is normal to have clearance between the shaft and the bearing, which will not affect the use. The use of this structure greatly reduces the friction resistance and prolongs the service life of the workpiece.
Question: How to deal with oil leakage in the received linear bearing?: Answer: Linear bearing is coated with anti-rust oil (except for MX grease device) when leaving the factory, which has little influence on grease. It is recommended to clean it before use and apply grease after drying.
Question: Can the linear bearing rotate?: Answer: The linear bearing is not suitable for rotating motion in structure. If it is forcibly rotated, it may cause damage to the product. If rotating motion is required, please give priority to linear type rotating bushings.

Check other FAQ (5 items) Hide

Product variants

Part Number
C-LMF20UU
C-LMF25UU
C-LMF30UU
E-LBF30UU
E-LBF35LUU
E-LBF35UU

Standard Unit Price	Minimum order quantity	Volume Discount	Days to Ship	RoHS	Inscribed Circle Dia. dr (Ø)	Overall Length L (mm)	Outer Cylinder Surface Treatment	Outer Dia. D (Ø)	Ball Recirculating Type	Length	Eccentricity (µm)	Basic Load Rating: Dynamic Load (Details) (N)	Basic Load Rating: Static Load (N)	Inscribed Circle Dia. Tolerance (Negative Side) (mm)	No.	Holder Material	Style of Mounting Hole
₹ 356.00	1 Piece(s)	Available	Same day Stock	10	20	42	No Surface Treatment	32	Single	Single	30	882	1370	-0.013	None	-	-
₹ 488.71	1 Piece(s)	Available	Same day Stock	10	25	59	No Surface Treatment	40	Single	Single	30	980	1570	-0.013	None	-	-
₹ 610.00	1 Piece(s)	Available	Same day Stock	10	30	64	No Surface Treatment	45	Single	Single	30	1570	2740	-0.013	None	-	-
₹ 741.00	1 Piece(s)	Available	15 Day(s)	10	30	64	No Surface Treatment	45	Single	Single	30	1570	2740	-0.021	-	-	Standard Counterbored Hole
₹ 2,314.27	1 Piece(s)	Available	Same day Stock	10	35	135	No Surface Treatment	52	Double	Double	0.04	2650	6270	-0.03	-	-	Standard Counterbored Hole
₹ 1,445.39	1 Piece(s)	Available	Same day Stock	10	35	70	No Surface Treatment	52	Single	Single	0.04	1670	3140	-0.021	-	Standard	Standard Counterbored Hole

Search by Category / Brand

Search by Category

How can we improve?