I bought MISUMI chains, but why can't I use them on my original sprocket?

Please confirm the specifications of the original sprocket and chain. Specification series number may not match. In addition, there are two specifications: A series and B series in China. The two specifications of sprocket chain are not universal.

Does the chain need routine maintenance after installation and use?

The chain needs regular maintenance after installation and use. These include daily lubricant application, confirmation of chain slack. The quality of lubrication will affect the life of the chain. Especially in recent years, high-speed use has been increasing, so it is necessary to take efficient lubrication methods.

In chain drive, where is the tensioning wheel usually installed?

Install the tensioning wheel on the inside of the loose edge of the belt close to the large pulley. It is often used when the center distance is not adjustable. The tensioning wheel is automatically pressed on the outside of the loose side of the belt close to the small wheel by using the suspending weight. It is used for applications where the transmission ratio is large and the center distance is small.

How to use the carrier chain?

The carrier chain can only be used for transmission, not for scenarios with large load and high positioning accuracy, please be careful!

Can the chain be cut off when it is extended?

It can be cut off. Our company has simple chain cutter available for selection.

Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 6:30 24/11/2024 to 4:30 (IST) 25/11/2024. We apologize for the inconvenience.
Please note that the MISUMI Pune office and warehouse will be closed on November 20th due to the state election.
Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(15 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

C-DRC35-16-10

Nominal Number of Teeth Shaft Bore Dia. d type CAD Days to Ship

Specification/Dimensions

Nominal
35

40

50

60

80
Clear
Number of Teeth(T)
9

11

12

13

15

16

17

18

19

25
Clear
Shaft Bore Dia. d(mm)
10

12

15

17

20
Clear
type
- C-DRC35
- C-DRC40
- C-DRC50
- C-DRC60
- C-DRC80
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

Same day

12 Day(s) or Less

18 Day(s) or Less
Clear

Specify Alterations

Idler Sprocket Japanese Standard Single Bearing

Click this image to zoom it.

Move the mouse over or click the image to zoom

Volume Discount

Check FAQ of this product (5 items)

Brand :

MiSUMi Economy

Part Number :

C-DRC35-16-10

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Product Overview of Idlers

■Sprocket Idlers is a sprocket with a built-in bearing. Its main function is to change the rotating direction of the driven wheel, tension the chain, adjust the pressure angle, and so on.
The Idlers is a part of the gear train that plays a transitional role. It does not change the transmission relationship. It is to make the force of the gear train more reasonable or to adapt to the layout of the entire transmission system.

■Only Idlers sprockets and chains with the same specifications can be used in combination.
This series is ISO standard 04C/ 06C/ 08A/ 10A/12A/16A (ANSI specifications 25B/ 35B/40B/50B/60B/80B) sprocket idlers.
■Do not use them with 04B/ 05B/ 06B/ 08B/ 10B/ 12B/ 16B series Idlers sprockets and chains, which may cause the chain sprocket mechanism to fail to operate normally!

Dimensional Drawing of Idlers

Ordinary ISO standard 04C/ 06C/ 08A/ 10A/12A/16A (ANSI specifications 25B/ 35B/ 40B/50B/60B/80B) sprocket Idlers,
Idler Dimensional Drawing

Specifications Overview of Idlers

Features: tension is applied to the chain, preventing the chain vibration, noise and poor engagement of the Idlers sprocket.
This series is ISO standard 04C/ 06C/ 08A/ 10A/12A/16A (ANSI specifications 25B/ 35B/40B/50B/60B/80B) sprocket Idlers, which can be used with our 25/ 35/40/50/60 /80 chains
■Do not use them with 08B/ 10B/ 12B/ 16B series chains, which may cause the chain sprocket mechanism to fail to operate normally!

Part Number of Idlers		Number of Teeth	d	Dp	Do	T	HD	L	Bearing			Applicable size of Idlers pin	Approximate weight (kg)
Type	No.								Part No.	b	Cr (dynamic rated load) kN	Single liner type bearing	DRC
Type	No.								Part No.	b	Steel	Single liner type bearing	DRC
Single bearing C-DRC	25	17	6	34.56	38	2.8	27	12	606ZZ	6	1.95	-	0.04	-
		19	8	38.58	42		31	13	608ZZ	7	3.3		0.08
		19	10	38.58	42		31	13	6900ZZ	6	2.7		0.08
	35	16	10	48.82	54	4.3	38	14	6000ZZ	8	4.55	IDP6000S	0.11
		16	12	48.82	54		38	14	6001ZZ	8	5.1	IDP6001S	0.1
		18	15	54.85	60		44	17	6202ZZ	11	7.65	IDP6202S	0.16
		25	20	76	81		60	21	6204ZZ	14	12.8	IDP6204S	0.33
	40	13	10	53.07	59	7.2	38	14	6000ZZ	8	4.55	IDP6000S	0.15
		13	12	53.07	59		38	14	6001ZZ	8	5.1	IDP6001S	0.14
		15	15	61.08	67		44	17	6202ZZ	11	7.65	IDP6202S	0.19
		17	17	69.12	76		53	19	6203ZZ	12	9.55	IDP6203S	0.3
		19	20	77.16	84		60	21	6204ZZ	14	12.8	IDP6204S	0.4
	50	12	12	61.34	69	8.7	43	16	6201ZZ	10	6.8	IDP6201S	0.21
		13	15	66.34	74		44	17	6202ZZ	11	7.65	IDP6202S	0.23
		15	17	76.35	84		53	19	6203ZZ	12	9.55	IDP6203S	0.37
		17	20	86.39	94		60	21	6204ZZ	14	12.8	IDP6204S	0.49
	60	11	12	67.62	76	11.7	44	16	6201ZZ	10	6.8	IDP6201S	0.26
		11	15	67.62	76		44	17	6202ZZ	11	7.65	IDP6202S	0.27
		14	20	85.61	95		60	21	6204ZZ	14	12.8	IDP6204S	0.56
	80	9	15	74.27	85	14.6	44	17	6202ZZ	11	7.65	IDP6202S	0.38
	80	11	20	90.16	102	14.6	60	21	6204ZZ	14	12.8	IDP6204S	0.69

Product Feature of Idlers

■Idlers Sprocket chain drive has the following features compared with gear drive and belt drive:
1. Idlers Multi-tooth load bearing, safe and reliable;
2. Flexible transmission, absorbing shock and vibration;
3. Large center distance range, low manufacturing and mounting accuracy requirements;
4. Compared with belt drive, the transmission ratio is accurate and the transmission efficiency is higher, suitable for high temperature.

■Two main purposes of the chain:
1. Idlers Connect the motor for transmission
2. Place the workpiece directly or indirectly on the chain for transfer

Example Use of Idlers

Used for driving power
A mechanism that can convert motor power into roller rotation by combining multiple Idlers sprockets and chains

Used for transporting workpieces of Idlers
A chain conveyor frame with high versatility using flat profiles and chain guides

Used for transporting workpieces of Idlers
A mechanism used to mount accessories on the chain, and extract and transport workpieces

Precautions of Idlers

Usage Method of Idlers

How to mount the roller chain

(A) Axis configuration
■Horizontal
Even when the two axes are arranged horizontally, the rotation direction of the axis must be considered.
The examples (2) and (3) in the figure show that when the chain is stretched, the disengagement between the Idlers sprocket teeth and the chain is not smooth and may bite.
In particular, the upper and lower chains in (3) will contact each other, so an Idlers is required.

■Vertical Idlers
If the chain is stretched, slack as shown in (5) will occur, and
when a small Idlers sprocket is used on the lower side, the chain may fall off. Therefore, please use it at an angle of 60 or less as shown in (4).
When it is necessary to use it vertically due to the mechanism or space, it is recommended to put the large sprocket on the lower side, and
use the idler on the outside or inside as shown in (6).

(B) Deflection Idlers
Deflection is generally about 4% of the shaft spacing, and about 2% in the following cases.
a. Vertical transmission or close to vertical transmission
b. Shaft spacing is more than 1m
c. When frequent heavy load starting and stopping are required
d. When reverse rotation is required

(C)When the load changes Idlers
If a tension adjuster is mounted on the tension side or slack side of the chain to provide initial tension in advance, it will eliminate vibration and reduce noise during operation.

Related Products of Idlers

Idlers Sprocket 60B

Specification Table of Idlers

Part Number of Idlers		Number of Teeth	d	Dp	Do	T	HD	L	Bearing			Applicable size of Idlers pin	Approximate weight (kg)
Type of Idlers	No.								Part No.	b	Cr (dynamic rated load) kN	Single liner type bearing	DRC	DRCS
Type of Idlers	No.								Part No.	b	Steel	Single liner type bearing	DRC	DRCS
Single Bearing DRC DRCS Double Bearing DRCW	25	17	6	34.56	38	2.8	27	12	606ZZ	6	1.95	-	0.04	-
		19	8	38.58	42		31	13	608ZZ	7	3.3		0.08
		19	10	38.58	42		31	13	6900ZZ	6	2.7		0.08
	35	16	10	48.82	54	4.3	38	14	6000ZZ	8	4.55	IDP6000S	0.11	0.12
		16	12	48.82	54		38	14	6001ZZ	8	5.1	IDP6001S	0.1	0.11
		18	15	54.85	60		44	17	6202ZZ	11	7.65	IDP6202S	0.16	0.17
		25	20	76	81		60	21	6204ZZ	14	12.8	IDP6204S	0.33	0.34
	40	13	10	53.07	59	7.2	38	14	6000ZZ	8	4.55	IDP6000S	0.15	0.16
		13	12	53.07	59		38	14	6001ZZ	8	5.1	IDP6001S	0.14	0.15
		15	15	61.08	67		44	17	6202ZZ	11	7.65	IDP6202S	0.19	0.2
		17	17	69.12	76		53	19	6203ZZ	12	9.55	IDP6203S	0.3	0.31
		19	20	77.16	84		60	21	6204ZZ	14	12.8	IDP6204S	0.4	0.41
	50	12	12	61.34	69	8.7	43	16	6201ZZ	10	6.8	IDP6201S	0.21	0.22
		13	15	66.34	74		44	17	6202ZZ	11	7.65	IDP6202S	0.23	0.24
		15	17	76.35	84		53	19	6203ZZ	12	9.55	IDP6203S	0.37	0.38
		17	20	86.39	94		60	21	6204ZZ	14	12.8	IDP6204S	0.49	0.5
	60	11	12	67.62	76	11.7	44	16	6201ZZ	10	6.8	IDP6201S	0.26	-
		11	15	67.62	76		44	17	6202ZZ	11	7.65	IDP6202S	0.27
		14	20	85.61	95		60	21	6204ZZ	14	12.8	IDP6204S	0.56
	80	9	15	74.27	85	14.6	44	17	6202ZZ	11	7.65	IDP6202S	0.38	-
	80	11	20	90.16	102	14.6	60	21	6204ZZ	14	12.8	IDP6204S	0.69	-

Specification Table

Features: tension is applied to the chain, preventing the chain vibration, noise and poor engagement of the sprocket.
This series is ISO standard 04C/ 06C/ 08A/ 10A/12A/16A (ANSI specifications 25B/ 35B/40B/50B/60B/80B) sprocket idlers, which can be used with our 25/ 35/40/50/60 /80 chains
■Do not use them with 08B/ 10B/ 12B/ 16B series chains, which may cause the chain sprocket mechanism to fail to operate normally!

Part Number		Number of Teeth	d	Dp	Do	T	HD	L	Bearing			Applicable size of idler pin	Approximate weight (kg)
Type	No.								Part No.	b	Cr (dynamic rated load) kN	Single liner type bearing	DRC	DRCS
Type	No.								Part No.	b	Steel	Single liner type bearing	DRC	DRCS
Single Bearing DRC DRCS Double Bearing DRCW	25	17	6	34.56	38	2.8	27	12	606ZZ	6	1.95	-	0.04	-
		19	8	38.58	42		31	13	608ZZ	7	3.3		0.08
		19	10	38.58	42		31	13	6900ZZ	6	2.7		0.08
	35	16	10	48.82	54	4.3	38	14	6000ZZ	8	4.55	IDP6000S	0.11	0.12
		16	12	48.82	54		38	14	6001ZZ	8	5.1	IDP6001S	0.1	0.11
		18	15	54.85	60		44	17	6202ZZ	11	7.65	IDP6202S	0.16	0.17
		25	20	76	81		60	21	6204ZZ	14	12.8	IDP6204S	0.33	0.34
	40	13	10	53.07	59	7.2	38	14	6000ZZ	8	4.55	IDP6000S	0.15	0.16
		13	12	53.07	59		38	14	6001ZZ	8	5.1	IDP6001S	0.14	0.15
		15	15	61.08	67		44	17	6202ZZ	11	7.65	IDP6202S	0.19	0.2
		17	17	69.12	76		53	19	6203ZZ	12	9.55	IDP6203S	0.3	0.31
		19	20	77.16	84		60	21	6204ZZ	14	12.8	IDP6204S	0.4	0.41
	50	12	12	61.34	69	8.7	43	16	6201ZZ	10	6.8	IDP6201S	0.21	0.22
		13	15	66.34	74		44	17	6202ZZ	11	7.65	IDP6202S	0.23	0.24
		15	17	76.35	84		53	19	6203ZZ	12	9.55	IDP6203S	0.37	0.38
		17	20	86.39	94		60	21	6204ZZ	14	12.8	IDP6204S	0.49	0.5
	60	11	12	67.62	76	11.7	44	16	6201ZZ	10	6.8	IDP6201S	0.26	-
		11	15	67.62	76		44	17	6202ZZ	11	7.65	IDP6202S	0.27
		14	20	85.61	95		60	21	6204ZZ	14	12.8	IDP6204S	0.56
	80	9	15	74.27	85	14.6	44	17	6202ZZ	11	7.65	IDP6202S	0.38	-
	80	11	20	90.16	102	14.6	60	21	6204ZZ	14	12.8	IDP6204S	0.69	-

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 45; 60

Part Number
C-DRC35-16-10
C-DRC35-16-12
C-DRC35-18-15
C-DRC35-25-20
C-DRC40-13-10
C-DRC40-13-12
C-DRC40-15-15
C-DRC40-17-17
C-DRC40-19-20
C-DRC50-12-12
C-DRC50-13-15
C-DRC50-17-20
C-DRC60-11-15
C-DRC80-9-15
C-DRC80-11-20

Price	Minimum Order Qty.	Volume Discount	Days to Ship	RoHS	Nominal	Number of Teeth (T)	Shaft Bore Dia. d (mm)
₹ 937.20	1 Piece(s)	Available	Same day	10	35	16	10
₹ 937.20	1 Piece(s)	Available	Same day	10	35	16	12
₹ 1,008.00	1 Piece(s)	Available	Same day	10	35	18	15
₹ 840.00	1 Piece(s)	Available	12 Day(s)	10	35	25	20
₹ 937.20	1 Piece(s)	Available	Same day	10	40	13	10
₹ 937.20	1 Piece(s)	Available	Same day	10	40	13	12
₹ 1,008.00	1 Piece(s)	Available	Same day	10	40	15	15
₹ 1,085.00	1 Piece(s)	Available	12 Day(s)	10	40	17	17
₹ 1,400.40	1 Piece(s)	Available	Same day	10	40	19	20
₹ 513.00	1 Piece(s)	Available	12 Day(s)	10	50	12	12
₹ 855.60	1 Piece(s)	Available	Same day	10	50	13	15
₹ 1,250.40	1 Piece(s)	Available	Same day	10	50	17	20
₹ 696.00	1 Piece(s)	Available	12 Day(s)	10	60	11	15
₹ 937.00	10 Piece(s)		18 Day(s)	10	80	9	15
₹ 785.00	1 Piece(s)	Available	12 Day(s)	10	80	11	20

Basic Information

Type	Idlers	Number of Strands	1	Material	Steel
Chain Type	RS	Shaft Type	Bearing Built-in, Single	Surface Treatment	Black Oxide

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: I bought MISUMI chains, but why can't I use them on my original sprocket?: Answer: Please confirm the specifications of the original sprocket and chain. Specification series number may not match. In addition, there are two specifications: A series and B series in China. The two specifications of sprocket chain are not universal.
Question: Does the chain need routine maintenance after installation and use?: Answer: The chain needs regular maintenance after installation and use. These include daily lubricant application, confirmation of chain slack. The quality of lubrication will affect the life of the chain. Especially in recent years, high-speed use has been increasing, so it is necessary to take efficient lubrication methods.
Question: In chain drive, where is the tensioning wheel usually installed?: Answer: Install the tensioning wheel on the inside of the loose edge of the belt close to the large pulley. It is often used when the center distance is not adjustable.
The tensioning wheel is automatically pressed on the outside of the loose side of the belt close to the small wheel by using the suspending weight. It is used for applications where the transmission ratio is large and the center distance is small.
Question: How to use the carrier chain?: Answer: The carrier chain can only be used for transmission, not for scenarios with large load and high positioning accuracy, please be careful!
Question: Can the chain be cut off when it is extended?: Answer: It can be cut off. Our company has simple chain cutter available for selection.

Check other FAQ (2 items) Hide

Search by Category / Brand

Search by Category

How can we improve?