What is the difference between ball bearing and roller bearing?

The contact between ball bearing and raceway is point contact, and the contact surface is oval when stressed. Because of the point contact, resisting force value is small, and the ball bearing is suitable for the application conditions of low torque and high rotational speed. They also have the characteristics of low noise. Ball bearings have low loading capacity but can bear radial and axial loads. The contact between roller bearing and raceway is line contact, and the contact surface is square when stressed. Because of the line contact, the torque of roller bearing is higher than that of ball bearing, and its rigidity is higher. Roller bearings have higher loading capacity, and cylindrical roller bearings have retaining edges to bear slight axial loads.

What is the classification of bearings according to the shape of rolling elements?

Rolling bearings are mainly divided into: ball bearings and roller bearings. Among them, ball bearings are divided into: deep groove ball bearings, angular contact bearings and radial thrust ball bearings. Roller bearings are divided into: cylindrical roller bearings, needle bearings, cone roller bearings and self-aligning roller bearings.

What is the classification of bearings according to load direction?

Bearing are divided into: radial bearings and thrust bearings according to the load direction. Among them, radial bearings are divided into: radial thrust ball bearings and radial roller bearings. Thrust bearings are divided into: thrust ball bearings and thrust roller bearings.

What is the basic rated life of rolling bearings?

The basic rated life of rolling bearings refers to the total number of revolutions that 90% of the ball bearings can rotate without peeling when eleven groups of ball bearings of the same kind and specification rotate respectively under the same conditions.

Can double shielded stainless steel deep groove ball bearings be directly used in corrosive environment?

The antirust performance of the material of double shielded stainless steel deep groove ball bearings is weaker than that of SUS3XX series stainless steel. Do not use it directly in corrosive environment.

Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(9 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

C-SEFL6700ZZ

Inner Dia. d Outer Dia. D Width B (or T) Basic Load Rating Cr (Dynamic) type CAD Days to Ship

Specification/Dimensions

Inner Dia. d(Ø)
10

12

15

17
Clear
Outer Dia. D(Ø)
15

18

19

21

22

24

28

30
Clear
Width B (or T)(mm)
4

5

6

7
Clear
Basic Load Rating Cr (Dynamic)(N)
407

468

473

868

1048

1283

1459

2185

3910
Clear
type
- C-SEFL67
- C-SEFL68
- C-SEFL69
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

Same day
Clear

Specify Alterations

Flanged Ball Bearings Stainless Steel

Name: Flanged Ball Bearings Stainless Steel
Brand: MISUMI
Availability: InStock

Click this image to zoom it.

Move the mouse over or click the image to zoom

Volume Discount

Check FAQ of this product (5 items)

Brand :

MISUMI

MiSUMi Economy

MISUMI

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Product Description

Flanged Ball Bearings Stainless Steel
Stainless steel ball bearings with flanged are commonly used in applications such as dental handpieces and miniature pumps. These bearings are available in various sizes to choose from.
[Feature]
● Bearing Size Standards: Metric System
● Inner Diameter (mm.) : 10, 12, 15 and 17
● Outer Diameter Minimum / Maximum (mm.) : 15 and 30
● Width (mm.) : 4, 5, 6 and 7
● Precision (JIS) : Class 0
● Bearing Type : Closed (Double Shielded (ZZ))
● Load Direction : Radial / Thrust Load or Axial Load
[Application]
It is used to support and guide rotating machine's components, such as shafts, wheels, pulleys ,etc

Economy Flanged Ball Bearings

Precision rotary componentsDouble-shielded bearingsIndustrial automation bearings

- Stainless steel construction for superior corrosion resistance

- Integrated flange design for easy mounting and positioning

- Double-shielded (ZZ) for enhanced dust protection

- Precision engineered to Class 0 standards for optimal performance

- Available in various medium inner diameters.

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product Overview of Ball Bearings

・ Deep groove Ball Bearings is the most commonly used rolling bearing. It is of simple structure and easy to use.
・ This kind of Ball Bearings has small friction coefficient and high limit speed.
・ The material of this bearing is equivalent to SUS440C, which has a certain antirust ability.
・ The noise level of this bearing reaches Z1.

Product Feature of Ball Bearings

・ The interface radius of the channel located on the inner and outer ring is slightly larger than the radius of the sphere, in arc shape. Mainly can bear radial load.
・ The friction torque is small, and accuracy grade is 0.

Dimensional Drawing of Ball Bearings

Product Dimensional Drawing of Ball Bearings
C-SEFL6901ZZ
Stainless steel small diameter ball bearing Double shielded

Material Equivalent to SUS440C
Bearing accuracy JIS B 1514 Grade 0
If rust prevention is required, please give priority to products with hard chromium plating, electroless nickel plated products or those made of stainless steel SUS3 series materials.

Example of Ball Bearings Use

Precautions for Using Ball Bearings

When the precision of the shaft and bearing housing is poor, the bearing will be affected, and its due performance will not be exerted. For example, the poor precision of the mounting part with the bearing will cause relative inclination of the inner and outer rings. At this time, besides the bearing load, the edge load will be increased additionally, which will shorten the fatigue life of the bearing, and even more seriously, it will lead to damage such as cage breakage and sticking.

Please use the following special mounting tool for installation and removal

Bearing heater	Proper installation of the Ball Bearings heater can guarantee a long life of the bearing. Rolling bearings are reliable mechanical components with long service life if they are installed and maintained correctly. After the induction heater is used for heating, the bearing expands outward in the cylindrical direction, which can avoid the damage during installation. Induction heater is one of the most scientific heating methods, which does not need preheating, and can be heated to 110℃ in a few seconds or minutes depending on the weight of bearings, without damaging the prior lubrication

Bearing puller	When the installation state of the Ball Bearings is in the following situations, the special puller can be used for disassembly. (a) Shaft shape: cylindrical shaft, Inner diameter shape of bearing inner ring: cylindrical hole. (b) Shaft shape: cylindrical shaft, inner diameter shape of bearing inner ring with tight bushing: tapered hole. (c) Shaft shape: tapered shaft, Inner diameter shape of bearing inner ring: tapered hole. In either state, the lock nut of the shaft (or the lock nut of the tight bushing) must be released during disassembly, and the lock nut must be placed in a loose state.

Related Products of Ball Bearings


Nut for Ball Bearings/Lock washer assembly	Heavy load lock nut	Ball Bearings grease
Typical model: JLNK20	Typical model: HLB10	Typical model: NS7

Specification Table of Ball Bearings

Part Number

C－SEFL6900ZZ

Key points of Ball Bearings economy series parts confirmation ①

Inner Diameter d (mm)		Clearance of MISUMI quality products (μm)		Clearance of economy series products (μm)
or More	or Less	Minimum	Max.	Minimum	Max.
Only 10		2	13	4	18
10	18	3	18	6	23
18	24	5	20	8	25
24	30	5	20	8	25

Part Number	d	D	B	D₁	C	r (min.)	Key points of Ball Bearings economy series parts confirmation ① Basic rated load		Allowable Rotational Speed rpm (Reference)	Mounting Dimensions		Weight (g) (Reference)
										Ds (min.)	R (max.)
							Cr (Dynamic) N	Cor (Static) N		Ds (min.)	R (max.)
C-SEFL6700ZZ	10	15	4	16.5	0.8	0.15	407	207	8000	10.3	0.15	2.1
C-SEFL6800ZZ		19	5	21	1	0.3	868	400	8000	12	0.3	6.1
C-SEFL6900ZZ		22	6	25	1.5	0.3	1283	606	8000	13.2		11.1
C-SEFL6701ZZ	12	18	4	19.5	0.8	0.2	468	252	8000	12.4	0.2	3.4
C-SEFL6901ZZ	12	24	6	26.5	1.5	0.3	1459	698	8000	14	0.3	13.2
C-SEFL6702ZZ	15	21	4	22.5	0.8	0.2	473	277	8000	15.4	0.2	3.9
C-SEFL6802ZZ		24	5	26	1.1	0.3	1048	596	8000	17	0.3	8.3
C-SEFL6902ZZ		28	7	30.5	1.5		2185	1075	8000	17		12
C-SEFL6903ZZ	17	30	7	32.5	1.5		3910	2210	8000	19		14

kgf＝N×0.101972

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 45; 60

Part Number
C-SEFL6700ZZ
C-SEFL6701ZZ
C-SEFL6702ZZ
C-SEFL6800ZZ
C-SEFL6802ZZ
C-SEFL6900ZZ
C-SEFL6901ZZ
C-SEFL6902ZZ
C-SEFL6903ZZ

Price	Minimum Order Qty.	Volume Discount	Days to Ship	RoHS	Inner Dia. d (Ø)	Outer Dia. D (Ø)	Width B (or T) (mm)	Basic Load Rating Cr (Dynamic) (N)	Basic Load Rating Cor (Static) (N)	Weight (g)
₹ 133.00	1 Piece(s)	Available	Same day	10	10	15	4	407	207	2.1
₹ 147.00	1 Piece(s)	Available	Same day	10	12	18	4	468	252	3.4
₹ 153.00	1 Piece(s)	Available	Same day	10	15	21	4	473	277	3.9
₹ 153.00	1 Piece(s)	Available	Same day	10	10	19	5	868	400	6.1
₹ 153.00	1 Piece(s)	Available	Same day	10	15	24	5	1048	596	8.3
₹ 153.00	1 Piece(s)	Available	Same day	10	10	22	6	1283	606	11.1
₹ 153.00	1 Piece(s)	Available	Same day	10	12	24	6	1459	698	13.2
₹ 162.00	1 Piece(s)	Available	Same day	10	15	28	7	2185	1075	19.9
₹ 259.00	1 Piece(s)	Available	Same day	10	17	30	7	3910	2210	21.4

Basic Information

Raceway Ring Shape	Ball	Bearing Type	Double Shielded	Outer Ring Type	With Flange
Inner/Outer Ring Material	Stainless Steel	Specifications, Environment	Standard / Dust Resistant	Precision (JIS)	Class 0
Load Direction	Radial / Thrust Load, Axial	Rolling Element Material	Stainless Steel	Size Standards	Metric System
Number of Raceway Ring Rows	Single Row	Allowable Rotational Speed(rpm)	8000

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: What is the difference between ball bearing and roller bearing?: Answer: The contact between ball bearing and raceway is point contact, and the contact surface is oval when stressed. Because of the point contact, resisting force value is small, and the ball bearing is suitable for the application conditions of low torque and high rotational speed. They also have the characteristics of low noise. Ball bearings have low loading capacity but can bear radial and axial loads. The contact between roller bearing and raceway is line contact, and the contact surface is square when stressed. Because of the line contact, the torque of roller bearing is higher than that of ball bearing, and its rigidity is higher. Roller bearings have higher loading capacity, and cylindrical roller bearings have retaining edges to bear slight axial loads.
Question: What is the classification of bearings according to the shape of rolling elements?: Answer: Rolling bearings are mainly divided into: ball bearings and roller bearings. Among them, ball bearings are divided into: deep groove ball bearings, angular contact bearings and radial thrust ball bearings. Roller bearings are divided into: cylindrical roller bearings, needle bearings, cone roller bearings and self-aligning roller bearings.
Question: What is the classification of bearings according to load direction?: Answer: Bearing are divided into: radial bearings and thrust bearings according to the load direction. Among them, radial bearings are divided into: radial thrust ball bearings and radial roller bearings. Thrust bearings are divided into: thrust ball bearings and thrust roller bearings.
Question: What is the basic rated life of rolling bearings?: Answer: The basic rated life of rolling bearings refers to the total number of revolutions that 90% of the ball bearings can rotate without peeling when eleven groups of ball bearings of the same kind and specification rotate respectively under the same conditions.
Question: Can double shielded stainless steel deep groove ball bearings be directly used in corrosive environment?: Answer: The antirust performance of the material of double shielded stainless steel deep groove ball bearings is weaker than that of SUS3XX series stainless steel. Do not use it directly in corrosive environment.

Check other FAQ (2 items) Hide

Search by Category / Brand

Search by Category

How can we improve?