Does the lock nut need to be greased?

Lubricant is required for both tightening and loosening. If the hardness of the fixed shaft is relatively low, please use a grease with high lubricity.

Precautions when fixing

In order to ensure the maximum effect of the lock nut, please expose at least 2 inches of the threaded part when fixing. Standard type lock nut is a round nut, with four small slots around its outer perimeter, which can be tightened on the stud body using a crescent wrench. The lock nut should be equipped with a shaft washer, which allows the small slot on the stud body to be fixed relative to its peripheral small slot, preventing its loosening.

Differences between a standard nut and a lock nut (1)

1. Vibration resistance is not the same Standard nut: inferior relative to the lock nut Lock nut: superior anti-vibration performance. When the thread is tightened, the top of thread of the bolt closely enters the 30° wedge-shaped slope of the nut to be clamped, and the normal force exerted on the wedge-shaped slope forms an angle of 60° with the axis of the bolt instead of The included angle of 30°. Therefore, the normal force generated when the locknut is tightened is much greater than that of the standard nut, and it has a great anti-loosening and anti-vibration ability.

Differences between a standard nut and a lock nut (2)

2. Wear resistance and shear resistance are not the same Standard nut: poor abrasion resistance and shear resistance; Lock nut: excellent wear resistance and shear resistance. The 30° inclined surface of thread bottom of the nut can make the nut locking force evenly distributed on all the threads of each ridge. Since the compression force on the thread surface of each ridge is evenly distributed, the nut can better solve the thread wear and shear deformation problem.

Differences between a standard nut and a lock nut (3)

3. The reutilization rate is not the same Standard nut: low reutilization rate; Lock nut: high reutilization rate. Extensive use shows that after repeated tightening and disassembly of the anti-loosening nut, its locking force is still not reduced, and the original locking can be maintained.

Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 6:30 24/11/2024 to 4:30 (IST) 25/11/2024. We apologize for the inconvenience.
Please note that the MISUMI Pune office and warehouse will be closed on November 20th due to the state election.
Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(1 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

C-FM50

type Nominal of Thread M CAD Days to Ship

Specification/Dimensions

type
- C-FM
Clear
Nominal of Thread M
M12X1.5

M15X1.0

M17X1.0

M20X1.0

M20X1.5

M24X1.5

M25X1.5

M30X1.5

M35X1.5

M40X1.5

M45X1.5

M50X1.5

M55X2.0

M60X2.0
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

Same day
Clear

Specify Alterations

Bearing Lock Nuts F Type 60-degree Clamping (C-FM50)

Name: Bearing Lock Nuts F Type 60-degree Clamping
Brand: MISUMI
Price: 1190.8 INR
Availability: InStock

Click this image to zoom it.

Move the mouse over or click the image to zoom

Volume Discount

Check FAQ of this product (5 items)

Brand :

MISUMI

MiSUMi Economy

MISUMI

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Economy Bearing Lock Nuts F Type 60-degree Clamping

Clamping Stable Reliable

- The Economy Series Bearing Lock Nuts deliver high performance at a budget-friendly price.

- Choose from a broad range of thread sizes for versatility in various applications.

- Made from strong materials with a locking pin, engineered to withstand demanding conditions.

- The clamping design provides a strong grip and stability, managing vibrations.

- Enjoy fast shipping and extensive inventory for timely delivery.

Economy Compact Precision Bearing Lock Nuts

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product Overview of Fulcrum Pins

Fulcrum Pins, Lock nut is widely used in machinery and other industries. Its working principle is self-locking by the friction between the nut and the bolt. But the reliability of this self-locking is reduced in dynamic loads. In some important occasions, we will take some anti-loosening measures to ensure the reliability of nut locking. The working principle of the nut is self-locking by the friction between the nut and the bolt. But the reliability of this self-locking is reduced in dynamic loads.

Product Feature of Fulcrum Pins

Structure and features of Fulcrum Pins
Features of Fulcrum Pins
In some important occasions we will take some anti-loosening measures to ensure the reliability of nut locking. Fulcrum Pins, Lock Nut is one of the anti-loosening measures.
Economic type F type lock nut (60° locking) Product Overview

Economic type F type lock nut (60° locking) Product Overview

Fulcrum Pins Locking copper and thread are designed at a 60° angle, and do not bear the axial load on the thread. When the nut is locked, the thread surface will not relieve the axial load

C-FM 60° locking copper design can withstand axial force and radial force at the same time

Dimensional Drawing of Fulcrum Pins

Economic type F type lock nut (60° locking) Dimensional Drawing

Specifications Overview of Fulcrum Pins

Economic type F type lock nut (60° locking) Specifications Overview

Fulcrum Pins, Axial vibration shock test result (Vibration frequency: 0.6cpm, acceleration: 8G)
Economic type F type lock nut (60° locking) Specifications Overview

Example Use of Fulcrum Pins

Economic type F type lock nut (60° locking) Example of use

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 45; 60

Part Number
C-FM50

Part Number	Price	Minimum Order Qty.	Volume Discount	Days to Ship	RoHS	Nominal of Thread M
	₹ 1,190.80	1 Piece(s)	Available	Same day	10	M50X1.5

Basic Information

Type	Lock Nut	Shape	Round Shape	Material	S45C Thermal Refined
Surface Treatment	Phosphate Conversion Coating	Screw Type	Metric (Fine) Thread

Please check the type/dimensions/specifications of the part C-FM50 in the Bearing Lock Nuts F Type 60-degree Clamping series.

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: Does the lock nut need to be greased?: Answer: Lubricant is required for both tightening and loosening. If the hardness of the fixed shaft is relatively low, please use a grease with high lubricity.
Question: Precautions when fixing: Answer: In order to ensure the maximum effect of the lock nut, please expose at least 2 inches of the threaded part when fixing. Standard type lock nut is a round nut, with four small slots around its outer perimeter, which can be tightened on the stud body using a crescent wrench. The lock nut should be equipped with a shaft washer, which allows the small slot on the stud body to be fixed relative to its peripheral small slot, preventing its loosening.
Question: Differences between a standard nut and a lock nut (1): Answer: 1. Vibration resistance is not the same
Standard nut: inferior relative to the lock nut
Lock nut: superior anti-vibration performance. When the thread is tightened, the top of thread of the bolt closely enters the 30° wedge-shaped slope of the nut to be clamped, and the normal force exerted on the wedge-shaped slope forms an angle of 60° with the axis of the bolt instead of The included angle of 30°. Therefore, the normal force generated when the locknut is tightened is much greater than that of the standard nut, and it has a great anti-loosening and anti-vibration ability.
Question: Differences between a standard nut and a lock nut (2): Answer: 2. Wear resistance and shear resistance are not the same
Standard nut: poor abrasion resistance and shear resistance;
Lock nut: excellent wear resistance and shear resistance. The 30° inclined surface of thread bottom of the nut can make the nut locking force evenly distributed on all the threads of each ridge. Since the compression force on the thread surface of each ridge is evenly distributed, the nut can better solve the thread wear and shear deformation problem.
Question: Differences between a standard nut and a lock nut (3): Answer: 3. The reutilization rate is not the same
Standard nut: low reutilization rate;
Lock nut: high reutilization rate. Extensive use shows that after repeated tightening and disassembly of the anti-loosening nut, its locking force is still not reduced, and the original locking can be maintained.

Check other FAQ (2 items) Hide

Product variants

Part Number
C-FM17
C-FM20
C-FM20-1
C-FM24
C-FM55
C-FM60

Standard Unit Price	Minimum order quantity	Volume Discount	Days to Ship	RoHS	Nominal of Thread M
₹ 683.80	1 Piece(s)	Available	Same day Stock	10	M17X1.0
₹ 730.60	1 Piece(s)	Available	Same day Stock	10	M20X1.0
₹ 730.60	1 Piece(s)	Available	Same day Stock	10	M20X1.5
₹ 765.70	1 Piece(s)	Available	Same day Stock	10	M24X1.5
₹ 1,374.10	1 Piece(s)	Available	Same day Stock	10	M55X2.0
₹ 1,457.30	1 Piece(s)	Available	Same day Stock	10	M60X2.0

Search by Category / Brand

Search by Category

How can we improve?