What is the difference between ball bearing and roller bearing?

The contact between ball bearing and raceway is point contact, and the contact surface is oval when stressed. Because of the point contact, resisting force value is small, and the ball bearing is suitable for the application conditions of low torque and high rotational speed. They also have the characteristics of low noise. Ball bearings have low loading capacity but can bear radial and axial loads. The contact between roller bearing and raceway is line contact, and the contact surface is square when stressed. Because of the line contact, the torque of roller bearing is higher than that of ball bearing, and its rigidity is higher. Roller bearings have higher loading capacity, and cylindrical roller bearings have retaining edges to bear slight axial loads.

What is the classification of bearings according to the shape of rolling elements?

Rolling bearings are mainly divided into: ball bearings and roller bearings. Among them, ball bearings are divided into: deep groove ball bearings, angular contact bearings and radial thrust ball bearings. Roller bearings are divided into: cylindrical roller bearings, needle bearings, cone roller bearings and self-aligning roller bearings.

What is the classification of bearings according to load direction?

Bearing are divided into: radial bearings and thrust bearings according to the load direction. Among them, radial bearings are divided into: radial thrust ball bearings and radial roller bearings. Thrust bearings are divided into: thrust ball bearings and thrust roller bearings.

What standard does the vibration class of this bearing meet?

The vibration class of the bearing is above Z1

Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 6:30 24/11/2024 to 4:30 (IST) 25/11/2024. We apologize for the inconvenience.
Please note that the MISUMI Pune office and warehouse will be closed on November 20th due to the state election.
Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(1 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

C-EFL675ZZ

type Inner Dia. d Outer Dia. D Width B (or T) Basic Load Rating Cr (Dynamic) CAD Days to Ship

Specification/Dimensions

type
- C-EFL6□□ZZ
Clear
Inner Dia. d(Ø)
3

4

5

6

8
Clear
Outer Dia. D(Ø)
6

7

8

9

10

11

12

13

14

15

16

17

19

22
Clear
Width B (or T)(mm)
2.5

3

3.5

4

5

6

7
Clear
Basic Load Rating Cr (Dynamic)(N)
146

152

155

273

326

361

392

399

441

448

501

670

756

910

931

945

1127

1210

1393

1533

1635

2345
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

Same day
Clear

Specify Alterations

Flanged Small Ball Bearings (C-EFL675ZZ)

Name: Flanged Small Ball Bearings
Brand: MISUMI
Price: 87 INR
Availability: InStock

Click this image to zoom it.

Move the mouse over or click the image to zoom

Volume Discount

Check FAQ of this product (4 items)

Brand :

MISUMI

MiSUMi Economy

MISUMI

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Product Description

Flanged Small Ball Bearings
Flanged small ball bearings are commonly used in applications such as dental handpieces and miniature pumps. These bearings are available in various sizes to choose from.
[Feature]
● Bearing Size Standards: Metric System
● Inner Diameter Minimum / Maximum (mm.) : 10 and 50
● Outer Diameter Minimum / Maximum (mm.) : 26 and 110
● Width Minimum / Maximum (mm.) : 8 and 27
● Precision (JIS) : Class 0
● Bearing Type : Closed (Double Shielded (ZZ))
● Load Direction : Radial Load
[Application]
It is used to support and guide rotating machine's components, such as shafts, wheels, pulleys ,etc

Economy Flanged Small Ball Bearing

ReliabilityHigh Speed CapabilityLow Torque

- Bearing Type: Deep groove ball bearing with a flange for added support.

- Material: Made of SUJ2 steel for durability and performance.

- Size Range: Compact size with inner diameters in specified range.

- High Speed Capability: Suitable for high-speed applications due to small size.

- Basic Load Capacity: Handles moderate radial loads for small-sized applications.

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

Product of Ball Bearings Overview

・ Light load, medium · low speed, special for medium precision rotation, realizing ultra-low price.
・ Ball Bearings It is made of industry standard bearing steel with high surface hardness and wear resistance.
・ The vibration class of the product of Ball Bearings is above Z1

Product of Ball Bearings Feature

・ The interface radius of the channel located on the inner and outer ring is slightly larger than the radius of the sphere, in arc shape. Mainly can bear radial load.
・ In addition to the open type Ball Bearings, there are bearings with steel dust cover, bearings with contact rubber seal packing and bearings with non-contact rubber seal packing, or bearings with stop ring on the outer diameter of outer ring.
・ Ball Bearings with dust cover or seal packing are sealed with proper amount of high-quality grease. Deep groove ball bearings generally adopt steel plate stamped cage, which has low friction torque and accuracy grade of 0.

Dimensiona Ball Bearingsl Drawing

Product Dimensional Drawing
(Economic type) Small diameter deep groove ball bearing with flange Double shielded

Example of Ball Bearings Use

Ball Bearings Motor
1 Motor

Ball Bearings Gear unit
2 Gear unit

Ball Bearings Machine tool
3 Machine tool

Precautions Ball Bearings

When the precision of the shaft and Ball Bearings housing is poor, the bearing will be affected, and its due performance will not be exerted. For example, the poor precision of the mounting part with the bearing will cause relative inclination of the inner and outer rings. At this time, besides the bearing load, the edge load will be increased additionally, which will shorten the fatigue life of the bearing, and even more seriously, it will lead to damage such as cage breakage and sticking.

Please use the following special mounting tool for installation and removal

Ball Bearings heater
Bearing heater

Proper installation of the bearing heater can guarantee a long life of the bearing.
Rolling Ball Bearings are reliable mechanical components with long service life if they are installed and maintained correctly.
After the induction heater is used for heating, the bearing expands outward in the cylindrical direction, which can avoid the damage during installation. Induction heater is one of the most scientific heating methods, which does not need preheating, and can be heated to 110℃ in a few seconds or minutes depending on the weight of bearings, without damaging the prior lubrication

Ball Bearings puller
Bearing puller

When the installation state of the Ball Bearings is in the following situations, the special puller can be used for disassembly.
(a) Shaft shape: cylindrical shaft, Inner diameter shape of bearing inner ring: cylindrical hole.
(b) Shaft shape: cylindrical shaft, inner diameter shape of bearing inner ring with tight bushing: tapered hole.
(c) Shaft shape: tapered shaft, Inner diameter shape of bearing inner ring: tapered hole. In either state, the lock nut of the shaft (or the lock nut of the tight bushing) must be released during disassembly, and the lock nut must be placed in a loose state.

Specification Ball Bearings Table

Key points of economy series parts confirmation ①

Inner Diameter d (mm)		Clearance of MISUMI quality products of Ball Bearings (μm)		Clearance of economy series products of Ball Bearings (μm)
or More	or Less	Minimum	Max.	Minimum	Max.
Less than 10		5	10	7	15

Part Number	d	D	B	D₁	C	r (min.)	Key points of economy series parts confirmation ② Basic Rated Load		Allowable Rotational Speed rpm (Reference)	Mounting Dimensions		Weight (g) (Reference)
										Ds (min.)	R (max.)
							Cr (Dynamic) N	Cor (Static) N		Ds (min.)	R (max.)
C－EFL673ZZ	3	6	2.5	7.2	0.6	0.1	146	52	8000	3.6	0.08	0.33
C－EFL683ZZ		7	3	8.1	0.8	0.1	273	91		3.9	0.1	0.53
C－EFL693ZZ		8	4	9.5	0.9	0.15	392	125		4.2	0.15	0.97
C－EFL603ZZ		9	5	10.5	1	0.15	399	131				1.63
C－EFL623ZZ		10	4	11.5	1	0.15	441	153				1.86
C－EFL674ZZ	4	7	2.5	8.2	0.6	0.1	155	62		4.6	0.08	0.35
C－EFL684ZZ		9	4	10.3	1	0.1	448	157		5	0.1	1.14
C－EFL694ZZ		11		12.5	1	0.15	501	193		5.2	0.15	1.96
C－EFL604ZZ		12		13.5		0.2	670	242		5.6	0.2	2.53
C－EFL624ZZ		13	5	15		0.2	910	340			0.2	3.53
C－EFL675ZZ	5	8	2.5	9.2	0.6	0.1	152	64			0.08	0.41
C－EFL685ZZ		11	5	12.5	1	0.15	501	197		6.2	0.15	2.18
C－EFL695ZZ		13	4	15		0.2	756	301		6.6	0.2	2.84
C－EFL605ZZ		14	5	16		0.2	931	354		6.6	0.2	3.85
C－EFL625ZZ		16	5	18		0.3	1,210	469		7.7	0.3	5.3
C－EFL676ZZ	6	10	3	11.2	0.6	0.1	326	137		6.6	0.1	0.77
C－EFL686ZZ		13	5	15	1.1	0.15	756	308		7	0.15	3.04
C－EFL696ZZ		15	5	17	1.2	0.2	945	371		7.6	0.2	4.26
C－EFL606ZZ		17	6	19	1.2	0.3	1,533	585		8	0.3	6.61
C－EFL626ZZ		19	6	22	1.5	0.3	1,635	620		8	0.3	9.09
C－EFL678ZZ	8	12	3.5	13.6	0.8	0.1	361	176		8.8	0.1	1.15
C－EFL688ZZ		16	5	18	1.1	0.2	1,127	497		9.6	0.2	4.47
C－EFL698ZZ		19	6	22	1.5	0.3	1,393	606		10	0.3	8.3
C－EFL608ZZ		22	7	25	1.5	0.3	2,345	980		10	0.3	13

kgf＝N×0.101972

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 45; 60

Part Number
C-EFL675ZZ

Part Number	Price	Minimum Order Qty.	Volume Discount	Days to Ship	RoHS	Inner Dia. d (Ø)	Outer Dia. D (Ø)	Width B (or T) (mm)	Basic Load Rating Cr (Dynamic) (N)	Basic Load Rating Cor (Static) (N)	Weight (g)
	₹ 87.00	1 Piece(s)	Available	Same day	10	5	8	2.5	152	64	0.41

Basic Information

Raceway Ring Shape	Ball	Bearing Type	Double Shielded	Outer Ring Type	With Flange
Inner/Outer Ring Material	SUJ2 Equiv.	Specifications, Environment	Standard / Dust Resistant	Precision (JIS)	Class 0
Load Direction	Radial	Rolling Element Material	SUJ2	Size Standards	Metric System
Number of Raceway Ring Rows	Single Row	Allowable Rotational Speed(rpm)	8000

Please check the type/dimensions/specifications of the part C-EFL675ZZ in the Flanged Small Ball Bearings series.

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: What is the difference between ball bearing and roller bearing?: Answer: The contact between ball bearing and raceway is point contact, and the contact surface is oval when stressed. Because of the point contact, resisting force value is small, and the ball bearing is suitable for the application conditions of low torque and high rotational speed. They also have the characteristics of low noise. Ball bearings have low loading capacity but can bear radial and axial loads. The contact between roller bearing and raceway is line contact, and the contact surface is square when stressed. Because of the line contact, the torque of roller bearing is higher than that of ball bearing, and its rigidity is higher. Roller bearings have higher loading capacity, and cylindrical roller bearings have retaining edges to bear slight axial loads.
Question: What is the classification of bearings according to the shape of rolling elements?: Answer: Rolling bearings are mainly divided into: ball bearings and roller bearings. Among them, ball bearings are divided into: deep groove ball bearings, angular contact bearings and radial thrust ball bearings. Roller bearings are divided into: cylindrical roller bearings, needle bearings, cone roller bearings and self-aligning roller bearings.
Question: What is the classification of bearings according to load direction?: Answer: Bearing are divided into: radial bearings and thrust bearings according to the load direction. Among them, radial bearings are divided into: radial thrust ball bearings and radial roller bearings. Thrust bearings are divided into: thrust ball bearings and thrust roller bearings.
Question: What standard does the vibration class of this bearing meet?: Answer: The vibration class of the bearing is above Z1

Check other FAQ (1 items) Hide

Product variants

Part Number
C-EFL606ZZ
C-EFL608ZZ
C-EFL623ZZ
C-EFL676ZZ
C-EFL678ZZ
C-EFL683ZZ

Standard Unit Price	Minimum order quantity	Volume Discount	Days to Ship	RoHS	Inner Dia. d (Ø)	Outer Dia. D (Ø)	Width B (or T) (mm)	Basic Load Rating Cr (Dynamic) (N)	Basic Load Rating Cor (Static) (N)	Weight (g)
₹ 75.00	1 Piece(s)	Available	Same day Stock	10	6	17	6	1533	585	6.61
₹ 87.00	1 Piece(s)	Available	Same day Stock	10	8	22	7	2345	980	13
₹ 75.00	1 Piece(s)	Available	Same day Stock	10	3	10	4	441	153	1.86
₹ 87.00	1 Piece(s)	Available	Same day Stock	10	6	10	3	326	137	0.77
₹ 87.00	1 Piece(s)	Available	Same day Stock	10	8	12	3.5	361	176	1.15
₹ 96.00	1 Piece(s)	Available	Same day Stock	10	3	7	3	273	91	0.53

Search by Category / Brand

Search by Category

How can we improve?