A coupling is a part that connects two different rotating bodies (motor shaft, ball screw, etc.) and aims at transmitting torque. The load of assembly adjustment is reduced by absorbing the axis deviation (lateral misalignment, angular misalignment and axial amplitude) between rotating bodies. And in case of accidental overload, the coupling is destroyed and the rotating bodies are disconnected to protect the expensive power part and the whole device.

What are the types of MISUMI couplings?

There are disc type, grooved type, cross type, claw type, bellows type, rigid type and universal joint type.

How to select coupling according to motor?

Disc type is recommended for servo motors, grooved type is recommended for stepping motors, and cross type is recommended for universal motors.

How to select according to the purpose, environment, working conditions?

Please refer to the MISUMI website.

What kind of coupling should be used when the angular misalignment is very large?

Please select the universal joint with allowable angular misalignment of 30 degrees. In addition, when grease cannot be applied regularly, use a rubber sleeve to fill grease and use it.

Which disc type coupling is better, single disc type or double disc type?

Double disc type can absorb angular misalignment and lateral misalignment, but the total length will increase. Although the total length of the single disc type is short, it is only suitable for applications with narrow space because lateral misalignment is not allowed in the structure. Special attention should be paid to centering during use.

How much is appropriate to insert the shaft into the coupling during installation?

Please select the length of the main body (coupling part) described in the product catalog. If the insertion amount is too short, the shaft may slip and the clamping part may be damaged; If the insertion amount is too long, it will be damaged due to shaft interference inside the coupling.

Why is it necessary to install a protection cover around the coupling?

Due to high-speed rotation, accidental contact may result in injury or entanglement of gloves, towels, etc. In addition, for some reasons, parts may be damaged or debris may be scattered. Therefore, be sure to install the safety protection cover.

What should I do if there is no matching shaft bore diameter?

Please select a product with changeable keyway width or available with keyway processing. MISUMI products are divided into MCSLCWK series (disc type), CPOC series (cross type) and MMJN series (claw type), etc.

Is it a defective product that has difference in groove gap width?

Since the difference is within the dimensional tolerance range, there is no problem.

Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 6:30 24/11/2024 to 4:30 (IST) 25/11/2024. We apologize for the inconvenience.
Please note that the MISUMI Pune office and warehouse will be closed on November 20th due to the state election.
Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(1 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

GSACL32-12-14

type Shaft Bore Dia. 1 d1 (or d) Shaft Bore Dia. 2 d2 (or d) O.D. Overall Length Allowable Torque Range Allowable Torque Allowable Lateral Misalignment CAD Days to Ship

Specification/Dimensions

type
- GSACL
Clear
Shaft Bore Dia. 1 d1 (or d)(Ø)
4

5

6

6.35

8

10

12
Clear
Shaft Bore Dia. 2 d2 (or d)(Ø)
5

6

8

10

12

14
Clear
O.D.(Ø)
16

20

25

32
Clear
Overall Length(mm)
23

26

31

41
Clear
Allowable Torque Range(N•m)
0.05~1.00

1.01~3.00

3.01~5.00
Clear
Allowable Torque(N•m)
0.5

1

2

4
Clear
Allowable Lateral Misalignment(mm)
0.1

0.15
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

Same day
Clear

Specify Alterations

Slit Couplings Long, Clamping Type (GSACL32-12-14)

Click this image to zoom it.

Move the mouse over or click the image to zoom

Volume Discount

Check FAQ of this product (10 items)

Brand :

MiSUMi Economy

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Product Description

Are economically priced with the quality/perforce kept to the same level as conventional products. Can serve as the substitute for CPLC Type.

coupling Product Overview

The parallel line coupling takes into account the shortening of slots without weakening the ability to bear and correct deviation. Short slots can enhance and overlap the torque rigidity of the coupling, so that it can bear considerable torque.
The parallel line coupling usually has 3 to 5 slots to deal with the problem of low torque rigidity.
The parallel line coupling takes into account the shortening of slots without weakening the ability to bear and correct deviation. Short slots can enhance and overlap the torque rigidity of the coupling, so that it can bear considerable torque.

coupling Product Feature

【Features/Characteristics】The metal elastic coupling is integrally formed with zero rotary clearance. Elastic action compensates radial, angular and axial deviations. Clockwise and counterclockwise rotary characteristics are identical. Positioning screw fixing. Aluminum alloy material
【Usage】Suitable for standard motors
【Precautions】Moment of inertia and weight are calculated at the maximum shaft dia.
【Type】Grooved type
【Body Material】Aluminum alloy
【Fixing System】Clamping screw fixing type
【Applicable Motors】Servo motors and stepping motors
■ Parallel line couplings are suitable for light load applications.

Dimensional coupling Drawing

【Economic type】Grooved coupling Clamping type Length-increased type: Related image

Material	Surface Treatment	Accessories
Aluminum	Alumite Treatment	Fastening Bolt

coupling Specification Table

D	d₁	d₂								L	ℓ	F	A	Fastening Bolt
D	d₁	d₂								L	ℓ	F	A	M (Coarse Thread)	Tightening torque (N·ｍ)
16	4	4	5							23	6.4	3.2	5.5	M2.5	1.0
16	5		5		8					23	6.4	3.2	5.5
20	5			6	8					26	7	3.5	6.5
20	6			6	8	10				26	7	3.5	6.5
25	6					10				31	8	4	8.5	M3	1.5
	6.35				8	10
	8				8	10		12
32	10					10	11	12	14	41	11	5.5	10.5	M4	3.5
32	12							12	14	41	11	5.5	10.5	M4	3.5

■Characteristic Value

D	Allowable torque (N·m)	Maximum rotational speed (rpm)	Moment of inertia (kg·m²)	Static torsional stiffness (N·m/rad)	Allowable lateral misalignment (mm)	Allowable Angular Misalignment ( ° )	Allowable axial amplitude (mm)	Weight (g)

16	0.5	10,000	7.0×10^－7	53	0.1	2	±0.4	9
20	1		1.6×10^－6	120				16
25	2		4.4×10^－6	260	0.15		±0.5	28
32	4		1.7×10^－5	550				66

Static torsional stiffness, moment of inertia and weight are the values at the maximum shaft dia..

coupling Precautions

■ Calibration and adjustment
1. The coupling allows axis deviation, and transmits rotation angle and torque, but when the axis deviation exceeds the allowable value, vibration will occur or the service life will be drastically reduced.
Be sure to make calibration and adjustment.
2. Axis deviation includes lateral misalignment (parallel error of two axes), angular misalignment (angular error of two axes) and axial amplitude (axial movement of shaft).
Please calibrate and adjust the shaft to ensure that the axis deviation is below the allowable value recorded in the dimension and performance table of each product.
3. The allowable value of axis deviation recorded in the dimension and performance table refers to the situation when either lateral misalignment, angular misalignment or axial amplitude occurs alone. When more than two axis deviations occur at the same time, the corresponding allowable values are halved respectively.
4. Axis deviation not only occurs when assembling to the device, but also is caused by vibration, thermal expansion and bearing wear in operation. Therefore, it is recommended to set the axis deviation below 1/3 of the allowable value.

Example of Use coupling


Use example of coupling 1: motor×gear box	Use example of coupling 2: motor×ball screw


Use example of coupling 3: motor×encoder	Use example of coupling 4: motor×measuring tester

coupling Usage Method

■Mounting method
STEP1 Insert the coupling
Confirm that the clamping bolt has been unscrewed, and then remove the dust, foreign matter and oil from the shaft and coupling bore.
Then, when inserting the coupling into the shaft, please be careful not to put the disc under excessive stress such as compression or tension.
STEP2 Use fixture to adjust
Please use fixture to adjust and fix the concentricity of the left and right hubs of the coupling with high accuracy.
STEP3 Simple lateral misalignment and angular misalignment confirmation
Under the condition of unscrewed bolts, make the coupling slide axially and confirm its smooth movement.
Then, rotate the coupling to make sure it moves smoothly.
Lateral misalignment is not allowed for single disc type coupling, so carry out positioning securely.
Simple lateral misalignment confirmation

Simple lateral misalignment confirmation

Simple angular misalignment confirmation

STEP4 Installation
Please adjust the shaft insertion amount according to the dimension ℓ in the product catalog, and use a torque wrench to tighten with the specified torque.
＊ If the specified torque cannot be reached once, please cross fasten the left and right clamps twice or three times.

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 45; 60

Part Number
GSACL32-12-14

Part Number	Price	Minimum Order Qty.	Volume Discount	Days to Ship	RoHS	Shaft Bore Dia. 1 d1 (or d) (Ø)	Shaft Bore Dia. 2 d2 (or d) (Ø)	O.D. (Ø)	Overall Length (mm)	Allowable Torque Range (N•m)	Allowable Torque (N•m)	Allowable Lateral Misalignment (mm)	Allowable Axial Misalignment (mm)	Moment of Inertia (kg･m²)
	₹ 2,392.94	1 Piece(s)	Available	Same day	10	12	14	32	41	3.01~5.00	4	0.15	0.5	1.7×10^-5

Days to Ship

Overview · Features

■Features: The quality and performance are the same as those of previous products, thus realizing low-cost supply. Interchangeable with CPLCN.

Product TOP

Basic Information

Series Name	Slit	Application	For Servo Motors / Stepping Motor	Features	High Torsional Rigidity / Zero Backlash / Low Moment of Inertia
Allowable Misalignment	Angular Misalignment / Eccentricity / Axial Misalignment	Max. Rotational Speed Range(r/min)	4001~10000	Body Material	Aluminum Alloy
Allowable Angular Misalignment(deg)	2	Product Category	Coupling Main Body	Allowable Lateral Misalignment Range(mm)	0.02~0.2
Max. Rotational Speed(r/min)	10000	Standard/Short	Standard Type	Shaft Bore Shape	Standard Bore
Shaft Tightening Method	Fastening Bolt

Please check the type/dimensions/specifications of the part GSACL32-12-14 in the Slit Couplings Long, Clamping Type series.

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: What is a coupling?: Answer: A coupling is a part that connects two different rotating bodies (motor shaft, ball screw, etc.) and aims at transmitting torque. The load of assembly adjustment is reduced by absorbing the axis deviation (lateral misalignment, angular misalignment and axial amplitude) between rotating bodies. And in case of accidental overload, the coupling is destroyed and the rotating bodies are disconnected to protect the expensive power part and the whole device.
Question: What are the types of MISUMI couplings?: Answer: There are disc type, grooved type, cross type, claw type, bellows type, rigid type and universal joint type.
Question: How to select coupling according to motor?: Answer: Disc type is recommended for servo motors, grooved type is recommended for stepping motors, and cross type is recommended for universal motors.
Question: How to select according to the purpose, environment, working conditions?: Answer: Please refer to the MISUMI website.
Question: What kind of coupling should be used when the angular misalignment is very large?: Answer: Please select the universal joint with allowable angular misalignment of 30 degrees. In addition, when grease cannot be applied regularly, use a rubber sleeve to fill grease and use it.
Question: Which disc type coupling is better, single disc type or double disc type?: Answer: Double disc type can absorb angular misalignment and lateral misalignment, but the total length will increase.
Although the total length of the single disc type is short, it is only suitable for applications with narrow space because lateral misalignment is not allowed in the structure. Special attention should be paid to centering during use.
Question: How much is appropriate to insert the shaft into the coupling during installation?: Answer: Please select the length of the main body (coupling part) described in the product catalog. If the insertion amount is too short, the shaft may slip and the clamping part may be damaged; If the insertion amount is too long, it will be damaged due to shaft interference inside the coupling.
Question: Why is it necessary to install a protection cover around the coupling?: Answer: Due to high-speed rotation, accidental contact may result in injury or entanglement of gloves, towels, etc. In addition, for some reasons, parts may be damaged or debris may be scattered. Therefore, be sure to install the safety protection cover.
Question: What should I do if there is no matching shaft bore diameter?: Answer: Please select a product with changeable keyway width or available with keyway processing. MISUMI products are divided into MCSLCWK series (disc type), CPOC series (cross type) and MMJN series (claw type), etc.
Question: Is it a defective product that has difference in groove gap width?: Answer: Since the difference is within the dimensional tolerance range, there is no problem.

Check other FAQ (7 items) Hide

Product variants

Part Number
GSACL16-4-5
GSACL16-5-5
GSACL16-5-8
GSACL20-5-6
GSACL20-5-8
GSACL20-6-6

Standard Unit Price	Minimum order quantity	Volume Discount	Days to Ship	RoHS	Shaft Bore Dia. 1 d1 (or d) (Ø)	Shaft Bore Dia. 2 d2 (or d) (Ø)	O.D. (Ø)	Overall Length (mm)	Allowable Torque Range (N•m)	Allowable Torque (N•m)	Allowable Lateral Misalignment (mm)	Allowable Axial Misalignment (mm)	Moment of Inertia (kg･m²)
₹ 1,630.13	1 Piece(s)	Available	Same day Stock	10	4	5	16	23	0.05~1.00	0.5	0.1	0.4	7.0×10^-7
₹ 1,630.13	1 Piece(s)	Available	Same day Stock	10	5	5	16	23	0.05~1.00	0.5	0.1	0.4	7.0×10^-7
₹ 1,620.53	1 Piece(s)	Available	Same day Stock	10	5	8	20	26	0.05~1.00	0.5	0.1	0.4	7.0×10^-7
₹ 860.00	1 Piece(s)	Available	Same day Stock	10	5	6	20	26	0.05~1.00	1	0.1	0.4	1.6×10^-6
₹ 860.00	1 Piece(s)	Available	Same day Stock	10	5	8	20	26	0.05~1.00	1	0.1	0.4	1.6×10^-6
₹ 1,630.13	1 Piece(s)	Available	Same day Stock	10	6	6	20	26	0.05~1.00	1	0.1	0.4	1.6×10^-6

Search by Category / Brand

Search by Category

How can we improve?