What are the types of MISUMI couplings?

There are disc type, grooved type, cross type, claw type, bellows type, rigid type and universal joint type.

How to select coupling according to motor?

Disc type is recommended for servo motors, grooved type is recommended for stepping motors, and cross type is recommended for universal motors.

How to select according to the purpose, environment, working conditions?

Please refer to the MISUMI website.

What kind of coupling should be used when the angular misalignment is very large?

Please select the universal joint with allowable angular misalignment of 30 degrees. In addition, when grease cannot be applied regularly, use a rubber sleeve to fill grease and use it.

Which disc type coupling is better, single disc type or double disc type?

Double disc type can absorb angular misalignment and lateral misalignment, but the total length will increase. Although the total length of the single disc type is short, it is only suitable for applications with narrow space because lateral misalignment is not allowed in the structure. Special attention should be paid to centering during use.

How much is appropriate to insert the shaft into the coupling during installation?

Please select the length of the main body (coupling part) described in the product catalog. If the insertion amount is too short, the shaft may slip and the clamping part may be damaged; If the insertion amount is too long, it will be damaged due to shaft interference inside the coupling.

Why is it necessary to install a protection cover around the coupling?

Due to high-speed rotation, accidental contact may result in injury or entanglement of gloves, towels, etc. In addition, for some reasons, parts may be damaged or debris may be scattered. Therefore, be sure to install the safety protection cover.

What should I do if there is no matching shaft bore diameter?

Please select a product with changeable keyway width or available with keyway processing. MISUMI products are divided into MCSLCWK series (disc type), CPOC series (cross type) and MMJN series (claw type), etc.

Is it a defective product that has difference in groove gap width?

Since the difference is within the dimensional tolerance range, there is no problem.

Scheduled Maintenance Notice: This site will be unavailable due to scheduled maintenance from 6:30 10/11/2024 to 3:30 (IST) 11/11/2024. We apologize for the inconvenience.
Please note that the MISUMI Pune office and warehouse will be closed on November 20th due to the state election.
Notice of End of Sales for Economy Series Pneumatic Equipment Category. More information.

How can we improve?

How can we improve?

Feedback

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

Thank you for your time.
Your feedback is essential for our continuous improvement
Privacy Policy

Thank you for your cooperation.

Thank you for your time.
Your feedback is essential for our continuous improvement
Please use the inquiry form.

Privacy Policy

Configure

Part number has not been determine

(145 Part Numbers Available)

Configure Remaining Specifications

Part Number Complete

C-SCPS16-4-4

Shaft Bore Dia. 1 d1 (or d) Shaft Bore Dia. 2 d2 (or d) O.D. Overall Length Allowable Torque Range Allowable Torque Allowable Angular Misalignment type CAD Days to Ship

Specification/Dimensions

Shaft Bore Dia. 1 d1 (or d)(Ø)
4

5

6

6.35

8

10

11

12

14

15

16

17

19

20

22

24

25
Clear
Shaft Bore Dia. 2 d2 (or d)(Ø)
4

5

6

6.35

8

10

11

12

14

15

16

17

19

20

22

24

25
Clear
O.D.(Ø)
16.6

21

28

34

46

54.5
Clear
Overall Length(mm)
16.6

16.7

21.5

23.3

29.8

37.2
Clear
Allowable Torque Range(N•m)
0.05~1.00

1.01~3.00

3.01~5.00

5.01~10.00

20.01~50.00
Clear
Allowable Torque(N•m)
0.5

1

1.5

4

10

25
Clear
Allowable Angular Misalignment(deg)
1

1.2

1.5
Clear
type
- C-SCPS
Clear
CAD
- 2D
- 3D
Clear

Days to Ship

All

9 Day(s) or Less
Clear

Specify Alterations

Disc Couplings High Regidity Single Disc, Clamping Type

Volume Discount

Check FAQ of this product (10 items)

Brand :

MiSUMi Economy

Part Number :

C-SCPS16-4-4

C-SCPS16-4-5

C-SCPS16-4-6

C-SCPS16-5-5

C-SCPS16-5-6

C-SCPS16-6-6

C-SCPS21-4-4

C-SCPS21-4-5

C-SCPS21-4-6

C-SCPS21-4-8

C-SCPS21-5-5

C-SCPS21-5-6

C-SCPS21-5-8

C-SCPS21-6-6

C-SCPS21-6-8

C-SCPS21-8-8

C-SCPS28-6-6

C-SCPS28-6-6.35

C-SCPS28-6-8

C-SCPS28-6-10

C-SCPS16-4-4

Order Qty :
Total Price :

---
Days to ship :

---

Select part number to Order Now/ Add to Cart

CAD Download

Economy High Rigidity Single Disc Coupling

High torqueZero backlashHigh speed

- Exceptional high torque capacity for robust performance in demanding applications

- Designed for precise torque transmission with zero backlash

- Capable of handling high rotational speeds up to specified RPM

- Easy clamping type installation for quick and secure setup

- Suitable for a wide range of temperatures

Economy High Rigidity Single Disc Coupling

MISUMI Standard

Cheaper Price

Product Variety

3D CAD
3D CAD Support

coupling Product Overview

The disc coupling is composed of several groups of discs (stainless steel thin plates) that are interlaced with two halves of the coupling with bolts, and each group of discs is formed by stacking several pieces.
The disc coupling relies on the elastic deformation of the disc to compensate for the relative displacement of the connected two shafts, which is a high-performance flexible coupling with strong metal components.
It is characterized by compact structure, no backlash, high strength, long service life, no rotation clearance, no influence of temperature and oil pollution, acid resistance, alkali resistance and corrosion resistance.
Applicable motor types: recommended for servo motors, stepping motors and general motors.

coupling Product Feature

■ Main characteristics of disc coupling
1. Strong ability to compensate for misalignment between two axes. Compared with tooth coupling, angular displacement can be doubled. In case of radial displacement, reaction force is small, flexibility is large, and certain axial, radial and angular displacements are allowed.
2. It has obvious shock absorption, no noise and no wear.
3. Suitable for working in high temperature (-80+300) and harsh environment, and operate safely under shock and vibration conditions.
4. High transmission efficiency, up to 99.86%. Especially suitable for medium, high speed and high power transmission.
5. Simple structure, light weight, small in size and convenient assembly and disassembly. It can be assembled and disassembled without moving the machine (models with intermediate shaft), and requiring no lubrication.
6. It can accurately transmit the rotational speed without slip, and can be used for transmission of precision machinery

Dimensional coupling Drawing

The rigidity is comparable to the high rigidity SCPW of previous products, and the cost is greatly reduced. The surface has not been oxidized, which may be rough.

【Economic type】Disc type coupling High flexibility clamping type (Single disc type) Servo motor applicable type: Related image

・Material Table

Type	Parts	[ M ] Material	[ S ] Surface Treatment	[ A ] Accessories
C－SCPS	Body	Aluminum	－	Hex socket bolt (Clamping bolt)
	Disc	Stainless Steel	－
	Lock Bolt	SCM435	Ferroferric Oxide Protective Film

coupling Specification Table

Please order after selecting part number and parameters according to the selection steps to . 【Economic type】Disc type coupling High flexibility clamping type (Single disc type) Servo motor applicable type: Related image

Please specify the shaft bore dia. within the range of d₁≤d₂.

Part Number ( Type· No.)	－	d₁	－	d₂
C－SCPS21	－	6	－	8

Part Number		d_1, d₂ selection (But d₁≤d₂)																	D	d₃	L	ℓ	F	A	Fastening Bolt
Type	No.	d_1, d₂ selection (But d₁≤d₂)																	D	d₃	L	ℓ	F	A	M	Tightening torque (N·m)
C－SCPS	16	4	5	6															16.6	6.5	16.6	7.2	3	5.3	M2.6	1.0
	21	4	5	6		8													21	9.5	16.7	7	3.5	7	M2.6	1.2
	28			6	6.35	8	10												28	12	21.5	9	4	9.5	M3	1.7
	34			6	6.35	8	10	11	12	14									34	15	23.3	9.8	5	12	M3	1.7
	46					8	10	11	12	14	15	16	17	19					46	22	29.8	12.6	6	16.5	M4	4.1
	55								12	14	15	16	17	19	20	22	24	25	54.5	26	37.2	16	7	20.5	M5	8.2

■Characteristic Value

Part Number		Allowable torque (N·m)	Allowable Angular Misalignment (°)	Static torsional stiffness (N·m/rad)	Maximum Rotational Speed (r/min)	Moment of inertia (kg·m²)	Allowable axial amplitude (mm)	Compensation coefficient	Weight (g)
Type	No.
C－SCPS	16	0.5	1.0	1000	10000	3.16×10^－7	±0.10	1.5	8
	21	1.0		1700		7.90×10^－7			12
	28	1.5	1.2	6000		3.24×10^－6			30
	34	4.0	1.5	8000		7.60×10^－6			45
	46	10.0		20000		3.23×10^－5	±0.15		105
	55	25.0		33000		8.19×10^－5			180

[ NG ]Lateral misalignment is not allowed for single disc type.
[ ! ]Lateral misalignment, angular misalignment and axial amplitude are all single allowable values. If there are multiple deviations at the same time, the allowable value of each deviation will be reduced to 1/2 of the original value.

■Shaft slip torque (N·m)
[ ! ]When the shaft slip torque is less than the allowable torque, please use it below the shaft slip torque.

Part Number		d₁, d₂
Type	No.	4	5	6	6.35	8	10	11	12	14	15	16	17	19	20	22	24	25
C－SCPS	16	0.5	0.5	0.5	－	－	－	－	－	－	－	－	－	－	－	－	－	－
	21	1.0	1.0	1.0	－	1.0	－	－	－	－	－	－	－	－	－	－	－	－
	28	－	－	1.5	1.5	1.5	1.5	－	－	－	－	－	－	－	－	－	－	－
	34	－	－	2.5	2.5	4.0	4.0	4.0	4.0	4.0	－	－	－	－	－	－	－	－
	46	－	－	－	－	6.0	6.0	8.0	8.0	8.0	8.0	10	10	10	－	－	－	－
	55	－	－	－	－	－	－	－	16	16	19	25	25	25	25	25	25	25

coupling Precautions

■ Calibration and adjustment
1. The coupling allows axis deviation, and transmits rotation angle and torque, but when the axis deviation exceeds the allowable value, vibration will occur or the service life will be drastically reduced.
Be sure to make calibration and adjustment.
2. Axis deviation includes lateral misalignment (parallel error of two axes), angular misalignment (angular error of two axes) and axial amplitude (axial movement of shaft).
Please calibrate and adjust the shaft to ensure that the axis deviation is below the allowable value recorded in the dimension and performance table of each product.
3. The allowable value of axis deviation recorded in the dimension and performance table refers to the situation when either lateral misalignment, angular misalignment or axial amplitude occurs alone. When more than two axis deviations occur at the same time, the corresponding allowable values are halved respectively.
4. Axis deviation not only occurs when assembling to the device, but also is caused by vibration, thermal expansion and bearing wear in operation. Therefore, it is recommended to set the axis deviation below 1/3 of the allowable value.

Example of Use coupling

(Economic type) Disc type coupling High flexibility clamping type (Double disc type) Servo motor applicable type Example of use

Use example of coupling 1: motor×gear box

Use example of coupling 2: motor×ball screw

Use example of coupling 3: motor×encoder

Use example of coupling 4: motor×measuring tester

coupling Usage Method

■Mounting method
STEP1 Insert the coupling
Confirm that the clamping bolt has been unscrewed, and then remove the dust, foreign matter and oil from the shaft and coupling bore.
Then, when inserting the coupling into the shaft, please be careful not to put the disc under excessive stress such as compression or tension.
STEP2 Use fixture to adjust
Please use fixture to adjust and fix the concentricity of the left and right hubs of the coupling with high accuracy.
STEP3 Simple lateral misalignment and angular misalignment confirmation
Under the condition of unscrewed bolts, make the coupling slide axially and confirm its smooth movement.
Then, rotate the coupling to make sure it moves smoothly.
Lateral misalignment is not allowed for single disc type coupling, so carry out positioning securely.

Simple lateral misalignment confirmation		Simple angular misalignment confirmation

STEP4 Installation
Please adjust the shaft insertion amount according to the dimension ℓ in the product catalog, and use a torque wrench to tighten with the specified torque.
＊ If the specified torque cannot be reached once, please cross fasten the left and right clamps twice or three times.

Part Number

Incomplete part number.
Please use left hand selections to complete a part number.

: 30; 45; 60

Part Number
C-SCPS16-4-4
C-SCPS16-4-5
C-SCPS16-4-6
C-SCPS16-5-5
C-SCPS16-5-6
C-SCPS16-6-6
C-SCPS21-4-4
C-SCPS21-4-5
C-SCPS21-4-6
C-SCPS21-4-8
C-SCPS21-5-5
C-SCPS21-5-6
C-SCPS21-5-8
C-SCPS21-6-6
C-SCPS21-6-8
C-SCPS21-8-8
C-SCPS28-6-6
C-SCPS28-6-6.35
C-SCPS28-6-8
C-SCPS28-6-10
C-SCPS28-6.35-6.35
C-SCPS28-6.35-8
C-SCPS28-6.35-10
C-SCPS28-8-8
C-SCPS28-8-10
C-SCPS28-10-10
C-SCPS34-6-6
C-SCPS34-6-6.35
C-SCPS34-6-8
C-SCPS34-6-10
C-SCPS34-6-11
C-SCPS34-6-12
C-SCPS34-6-14
C-SCPS34-6.35-6.35
C-SCPS34-6.35-8
C-SCPS34-6.35-10
C-SCPS34-6.35-11
C-SCPS34-6.35-12
C-SCPS34-6.35-14
C-SCPS34-8-8
C-SCPS34-8-10
C-SCPS34-8-11
C-SCPS34-8-12
C-SCPS34-8-14
C-SCPS34-10-10
C-SCPS34-10-11
C-SCPS34-10-12
C-SCPS34-10-14
C-SCPS34-11-11
C-SCPS34-11-12
C-SCPS34-11-14
C-SCPS34-12-12
C-SCPS34-12-14
C-SCPS34-14-14
C-SCPS46-8-8
C-SCPS46-8-10
C-SCPS46-8-12
C-SCPS46-8-14
C-SCPS46-8-15
C-SCPS46-8-16

Price	Minimum Order Qty.	Volume Discount	Days to Ship	Shaft Bore Dia. 1 d1 (or d) (Ø)	Shaft Bore Dia. 2 d2 (or d) (Ø)	O.D. (Ø)	Overall Length (mm)	Allowable Torque Range (N•m)	Allowable Torque (N•m)	Allowable Angular Misalignment (deg)	Allowable Axial Misalignment (mm)	Moment of Inertia (kg･m²)
₹ 3,631.36	1 Piece(s)	Available	9 Day(s)	4	4	16.6	16.6	0.05~1.00	0.5	1	0.1	3.16×10^-7
₹ 3,631.36	1 Piece(s)	Available	9 Day(s)	4	5	16.6	16.6	0.05~1.00	0.5	1	0.1	3.16×10^-7
₹ 3,631.36	1 Piece(s)	Available	9 Day(s)	4	6	16.6	16.6	0.05~1.00	0.5	1	0.1	3.16×10^-7
₹ 3,630.02	1 Piece(s)	Available	9 Day(s)	5	5	16.6	16.6	0.05~1.00	0.5	1	0.1	3.16×10^-7
₹ 3,630.02	1 Piece(s)	Available	9 Day(s)	5	6	16.6	16.6	0.05~1.00	0.5	1	0.1	3.16×10^-7
₹ 3,630.02	1 Piece(s)	Available	9 Day(s)	6	6	16.6	16.6	0.05~1.00	0.5	1	0.1	3.16×10^-7
₹ 3,000.90	1 Piece(s)	Available	9 Day(s)	4	4	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 2,999.85	1 Piece(s)	Available	9 Day(s)	4	5	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 2,999.85	1 Piece(s)	Available	9 Day(s)	4	6	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 2,999.85	1 Piece(s)	Available	9 Day(s)	4	8	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 2,998.45	1 Piece(s)	Available	9 Day(s)	5	5	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 2,998.45	1 Piece(s)	Available	9 Day(s)	5	6	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 2,998.45	1 Piece(s)	Available	9 Day(s)	5	8	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 2,998.45	1 Piece(s)	Available	9 Day(s)	6	6	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 2,998.45	1 Piece(s)	Available	9 Day(s)	6	8	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 2,998.45	1 Piece(s)	Available	9 Day(s)	8	8	21	16.7	0.05~1.00	1	1	0.1	7.9×10^-7
₹ 4,304.27	1 Piece(s)	Available	9 Day(s)	6	6	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 4,304.27	1 Piece(s)	Available	9 Day(s)	6	6.35	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 4,301.71	1 Piece(s)	Available	9 Day(s)	6	8	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 4,301.71	1 Piece(s)	Available	9 Day(s)	6	10	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 4,304.27	1 Piece(s)	Available	9 Day(s)	6.35	6.35	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 4,301.71	1 Piece(s)	Available	9 Day(s)	6.35	8	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 4,301.71	1 Piece(s)	Available	9 Day(s)	6.35	10	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 4,301.57	1 Piece(s)	Available	9 Day(s)	8	8	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 4,301.57	1 Piece(s)	Available	9 Day(s)	8	10	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 4,301.57	1 Piece(s)	Available	9 Day(s)	10	10	28	21.5	1.01~3.00	1.5	1.2	0.1	3.24×10^-6
₹ 5,250.31	1 Piece(s)	Available	9 Day(s)	6	6	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,250.31	1 Piece(s)	Available	9 Day(s)	6	6.35	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,248.98	1 Piece(s)	Available	9 Day(s)	6	8	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,248.98	1 Piece(s)	Available	9 Day(s)	6	10	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.66	1 Piece(s)	Available	9 Day(s)	6	11	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.66	1 Piece(s)	Available	9 Day(s)	6	12	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,244.80	1 Piece(s)	Available	9 Day(s)	6	14	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,250.31	1 Piece(s)	Available	9 Day(s)	6.35	6.35	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,248.98	1 Piece(s)	Available	9 Day(s)	6.35	8	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,248.98	1 Piece(s)	Available	9 Day(s)	6.35	10	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.79	1 Piece(s)	Available	9 Day(s)	6.35	11	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.66	1 Piece(s)	Available	9 Day(s)	6.35	12	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,244.80	1 Piece(s)	Available	9 Day(s)	6.35	14	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.66	1 Piece(s)	Available	9 Day(s)	8	8	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.66	1 Piece(s)	Available	9 Day(s)	8	10	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.89	1 Piece(s)	Available	9 Day(s)	8	11	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.89	1 Piece(s)	Available	9 Day(s)	8	12	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,244.80	1 Piece(s)	Available	9 Day(s)	8	14	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.66	1 Piece(s)	Available	9 Day(s)	10	10	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.89	1 Piece(s)	Available	9 Day(s)	10	11	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,247.89	1 Piece(s)	Available	9 Day(s)	10	12	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,244.80	1 Piece(s)	Available	9 Day(s)	10	14	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,244.80	1 Piece(s)	Available	9 Day(s)	11	11	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,244.80	1 Piece(s)	Available	9 Day(s)	11	12	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,243.47	1 Piece(s)	Available	9 Day(s)	11	14	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,244.80	1 Piece(s)	Available	9 Day(s)	12	12	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,243.47	1 Piece(s)	Available	9 Day(s)	12	14	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,242.15	1 Piece(s)	Available	9 Day(s)	14	14	34	23.3	3.01~5.00	4	1.5	0.1	7.6×10^-6
₹ 5,066.82	1 Piece(s)	Available	9 Day(s)	8	8	46	29.8	5.01~10.00	10	1.5	0.15	3.23×10^-5
₹ 5,067.18	1 Piece(s)	Available	9 Day(s)	8	10	46	29.8	5.01~10.00	10	1.5	0.15	3.23×10^-5
₹ 5,065.40	1 Piece(s)	Available	9 Day(s)	8	12	46	29.8	5.01~10.00	10	1.5	0.15	3.23×10^-5
₹ 5,064.21	1 Piece(s)	Available	9 Day(s)	8	14	46	29.8	5.01~10.00	10	1.5	0.15	3.23×10^-5
₹ 5,063.03	1 Piece(s)	Available	9 Day(s)	8	15	46	29.8	5.01~10.00	10	1.5	0.15	3.23×10^-5
₹ 5,063.03	1 Piece(s)	Available	9 Day(s)	8	16	46	29.8	5.01~10.00	10	1.5	0.15	3.23×10^-5

Basic Information

Series Name	Disc	Application	For Servo Motors	Features	High Torsional Rigidity / High Torque Type / Zero Backlash
Allowable Misalignment	Angular Misalignment / Axial Misalignment	Max. Rotational Speed Range(r/min)	4001~10000	Body Material	Aluminum Alloy
Product Category	Coupling Main Body	Max. Rotational Speed(r/min)	10000	Disc Material	Stainless Steel
Single/Double	Single	Shaft Bore Shape	Standard Bore	Shaft Tightening Method	Fastening Bolt

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Frequently asked question (FAQ)

Question: What is a coupling?: Answer: A coupling is a part that connects two different rotating bodies (motor shaft, ball screw, etc.) and aims at transmitting torque. The load of assembly adjustment is reduced by absorbing the axis deviation (lateral misalignment, angular misalignment and axial amplitude) between rotating bodies. And in case of accidental overload, the coupling is destroyed and the rotating bodies are disconnected to protect the expensive power part and the whole device.
Question: What are the types of MISUMI couplings?: Answer: There are disc type, grooved type, cross type, claw type, bellows type, rigid type and universal joint type.
Question: How to select coupling according to motor?: Answer: Disc type is recommended for servo motors, grooved type is recommended for stepping motors, and cross type is recommended for universal motors.
Question: How to select according to the purpose, environment, working conditions?: Answer: Please refer to the MISUMI website.
Question: What kind of coupling should be used when the angular misalignment is very large?: Answer: Please select the universal joint with allowable angular misalignment of 30 degrees. In addition, when grease cannot be applied regularly, use a rubber sleeve to fill grease and use it.
Question: Which disc type coupling is better, single disc type or double disc type?: Answer: Double disc type can absorb angular misalignment and lateral misalignment, but the total length will increase.
Although the total length of the single disc type is short, it is only suitable for applications with narrow space because lateral misalignment is not allowed in the structure. Special attention should be paid to centering during use.
Question: How much is appropriate to insert the shaft into the coupling during installation?: Answer: Please select the length of the main body (coupling part) described in the product catalog. If the insertion amount is too short, the shaft may slip and the clamping part may be damaged; If the insertion amount is too long, it will be damaged due to shaft interference inside the coupling.
Question: Why is it necessary to install a protection cover around the coupling?: Answer: Due to high-speed rotation, accidental contact may result in injury or entanglement of gloves, towels, etc. In addition, for some reasons, parts may be damaged or debris may be scattered. Therefore, be sure to install the safety protection cover.
Question: What should I do if there is no matching shaft bore diameter?: Answer: Please select a product with changeable keyway width or available with keyway processing. MISUMI products are divided into MCSLCWK series (disc type), CPOC series (cross type) and MMJN series (claw type), etc.
Question: Is it a defective product that has difference in groove gap width?: Answer: Since the difference is within the dimensional tolerance range, there is no problem.

Check other FAQ (7 items) Hide

Search by Category / Brand

Search by Category

How can we improve?