(!)NOTE : Windows 7 users won’t be able to use some latest features of eCatalog/WOS since Microsoft is ending support for Windows 7 on 14 Jan, 2020. Please upgrade your system for uninterrupted services.

Carbide Drill Recommended Cutting Conditions

Model Number
TAC-RESDBA / TAC-RESDRA / TAC-RFESDB / TAC-RFESDRA / TAC-HESDB / TAC-HESDR


■ Cutting Speeds, Rotational Speeds and Feed Amounts
Title image sampleWhen abnormal vibration or sounds occur during cutting, adjust the cutting conditions.
Title image sample
Title image sample
For TAC-WMESDRA, refer to the above conditions for TAC-RESDRA and use similarly.
Title image sampleFor TAC-CR-RFESDBA / TAC-CR-RFESDRA / TAC-CR-RFSDB / TAC-CR-RFSDR / TAC-ESDBA / TAC-ESDRA, refer to the above conditions for TAC-RFESDRA and use similarly.
Title image sampleFor TAC-RSDB / TAC-RSDR / TSC-DL-ESDB / TSC-DL-ESDR / TAC-DL-SESDR, refer to the above conditions for TAC-RESDRA and use similarly.
Title image sampleFor TAC-HRESDB / TAC-HRESDR, increase the rotational speed by 10 to 20% from the above conditions for TAC-RESDRA, and use similar feed amount conditions.
Model Number
TAC-ESDB / TAC-ESDR / TAC-MS-ESDR


■ Cutting Speeds, Rotational Speeds and Feed Amounts
Title image sampleWhen abnormal vibration or sounds occur during cutting, adjust the cutting conditions.
Title image sample
Title image sample
For TAC-WMESDRA, use under conditions increased by 20 to 30% from the above conditions for TAC-ESDR.
Model Number
TAC-SDB / TAC-SDS / C-SDB / C-SDS / TAC-SDXL


■ Cutting Speeds, Rotational Speeds and Feed Amounts
Title image sampleWhen abnormal vibration or sounds occur during cutting, adjust the cutting conditions.
Title image sample
Title image sampleFor TAC-HSDXL, use under conditions increased by 20 to 30% from the above conditions for TAC-SDXL.

Title image sampleThe above cutting conditions for TAC-SDXL / TAC-HSDXL have been set based on 10 x D. In the case of depths other than these, adjust these conditions by referring to the table below.
Title image sample

TiAℓN Coated Carbide Drill / Type With Burnishing Blade, 3-Flute Type

Model Number
TAC-BNESDBA / TAC-ESD3FRA / TAC-ESD3FB

Title image sample
Title image sampleFor TAC-HBNESDR, use under conditions increased by 20 to 40% from the above conditions for TAC-BNESDBA.

TiAℓN Coated Carbide Stepped Drill

Model Number
TAC-SC-SDR / TAC-SF-SDR / C-SC-TSDR

Title image sample

TiAℓN Coated Carbide Drill / Long Neck Type

Model Number
TAC-ESD2LB

Title image sample

TS Coated Carbide Drill for High-Hardness Steel Machining

Model Number
TSC-CR-XESDR / TSC-XESDR / TSC-XESDM / TSC-XSDR / TSC-XSDM

Title image sample

TS Coated Carbide Drill for High-Hardness Steel Machining / Small Diameter Type

Model Number
TSC-MS-XESDB / TSC-MS-XESDR
Title image sample

TS Coated Carbide Drill for High-Hardness Steel Machining / Long Neck Type

Model Number
TSC-XESD2LB

Title image sample

DLC Coated Carbide Drill for Aluminum Machining

Model Number
DLC-ALESDR / DLC-DL-ALESDR

Title image sample

DLC Coated Carbide Stepped Drill for Aluminum Machining

Model Number
DLC-SC-SDR / DLC-SF-SDR

Title image sample

TiAℓN Coated Carbide Drill for Cast Iron Machining

Model Number
TAC-FCESD3R

Title image sample

Carbide Drill for Resin Machining

Model Number
SEC-PLSDB

Title image sample

Burnishing Drill

Model Number
BUNDR / BUNDRS

Title image sample

TiAℓN Coated Carbide NC Spot Drill

Model Number
TAC-NCSPD / TAC-LS-NCSPD / TAC-MS-HNCSPD

Title image sample
Title image sample
For TAC-LS-NCSPD, use with feed amount lowered by about 20 to 30%.
Title image sampleWhen performing V groove machining on the TAC-MS-HNCSPD, use with feed speed lowered by about 30 to 50%.
Title image sampleFor SEC-NCSPD, use with the rotational speed and feed amount lowered by about 20 to 30%.

TiAℓN Coated Carbide Center Drill

Model Number
TAC-CTDA / TAC-CTDAL / TAC-CTDACW

Title image sample
Title image sample
For TAC-CTDAL, use with feed amount lowered by about 20 to 30%.

TiAℓN Coated Carbide Countersink

Model Number
TAC-CS3M / TAC-LS-CS3M

Title image sample
Title image sample
For TAC-LS-CS3M, use with feed amount lowered by about 20 to 30%.